DISH Network 512 用户手册
Page 99
Troubleshooting Tables
013, 014
•
You may have tried to tune to a
program on a channel which you
have not bought.
program on a channel which you
have not bought.
•
You must buy a channel before you can tune to a program on
that channel. Call the Customer Service Center to buy the
channel, or if you believe this message was displayed by
mistake.
that channel. Call the Customer Service Center to buy the
channel, or if you believe this message was displayed by
mistake.
015
•
You may have just plugged in the
receiver, and it is acquiring the
satellite signal. Or, the receiver
may have temporarily lost the
signal.
receiver, and it is acquiring the
satellite signal. Or, the receiver
may have temporarily lost the
signal.
•
Wait a few minutes to see if the message is removed. Make sure
that all required cables are in place, and check that all cable
connections are tight and dry (for outdoor cables).
Make sure that the satellite dish has a clear line of sight to the
satellite. Check whether branches or leaves have grown into the
line of sight.
that all required cables are in place, and check that all cable
connections are tight and dry (for outdoor cables).
Make sure that the satellite dish has a clear line of sight to the
satellite. Check whether branches or leaves have grown into the
line of sight.
•
Check that the Signal Strength bar in the Point Dish/
Signal menu is green and displays the word Locked. If not,
contact your installer to re-aim the satellite dish.
Signal menu is green and displays the word Locked. If not,
contact your installer to re-aim the satellite dish.
018
•
The receiver may not be
connected to an active telephone
line.
connected to an active telephone
line.
•
The credit limit may have been
exceeded.
exceeded.
•
You must connect the receiver to an active telephone connection
at all times. If you install two or more receivers, you must
connect each receiver to an active telephone connection at all
times.
at all times. If you install two or more receivers, you must
connect each receiver to an active telephone connection at all
times.
•
Call the Customer Service Center for help checking the credit
limit, and/or to get authorization to make a purchase.
limit, and/or to get authorization to make a purchase.
022
•
The satellite dish may have
moved so that it is no longer
picking up the satellite signal.
The cable connections may have
loosened or have moisture inside.
There may be an interruption of
the satellite signal.
moved so that it is no longer
picking up the satellite signal.
The cable connections may have
loosened or have moisture inside.
There may be an interruption of
the satellite signal.
•
If you have authorized the receiver, wait a few minutes to see if
the message is removed. Make sure that all required cables are
in place, and check that all cable connections are tight and dry
(for outdoor cables).
the message is removed. Make sure that all required cables are
in place, and check that all cable connections are tight and dry
(for outdoor cables).
•
Make sure that the satellite dish has a clear line of sight to the
satellite. Check whether branches or leaves have grown into the
line of sight.
satellite. Check whether branches or leaves have grown into the
line of sight.
•
Check that the Signal Strength bar in the Point Dish/
Signal menu is green and displays the word Locked. If not,
contact your installer to re-aim the satellite dish. If you have not
authorized the receiver, call the Customer Service Center for
help.
Signal menu is green and displays the word Locked. If not,
contact your installer to re-aim the satellite dish. If you have not
authorized the receiver, call the Customer Service Center for
help.
026
•
The receiver may have
temporarily lost the satellite
signal.
temporarily lost the satellite
signal.
•
Wait a few minutes to see if the message is removed. Make sure
that all required cables are in place, and check that all cable
connections are tight and dry (for outdoor cables).
Make sure that the satellite dish has a clear line of sight to the
satellite. Check whether branches or leaves have grown into the
line of sight.
that all required cables are in place, and check that all cable
connections are tight and dry (for outdoor cables).
Make sure that the satellite dish has a clear line of sight to the
satellite. Check whether branches or leaves have grown into the
line of sight.
•
Check that the Signal Strength bar in the Point Dish/
Signal menu is green and displays the word Locked. If not,
contact your installer to re-aim the satellite dish.
Signal menu is green and displays the word Locked. If not,
contact your installer to re-aim the satellite dish.
028
•
Pay Per View events cannot be
purchased until the receiver has
downloaded new software.
purchased until the receiver has
downloaded new software.
•
Turn the receiver off via the remote "Power" button and do not
disturb for the next 15 minutes. To change channels, press the
"Up" or "Down" arrow button on the remote or use the "Recall"
button to return to the last viewed channel.
disturb for the next 15 minutes. To change channels, press the
"Up" or "Down" arrow button on the remote or use the "Recall"
button to return to the last viewed channel.
032
•
You may have tried to set a VCR
Event Timer without having set
up the receiver to control the
VCR.
Event Timer without having set
up the receiver to control the
VCR.
•
You must set up the receiver to control the VCR before you can
set a VCR Event Timer. See the Using the System for
instructions.
set a VCR Event Timer. See the Using the System for
instructions.
059
•
You may have tried to close an
installation menu without having
done the Check Switch test.
installation menu without having
done the Check Switch test.
•
If your setup includes a multi-dish switch, you must do
the Check Switch test.
the Check Switch test.
060
•
You may have aimed the satellite
dish at one satellite, but selected
the option for another satellite on
the Point Dish/Signal menu.
dish at one satellite, but selected
the option for another satellite on
the Point Dish/Signal menu.
•
Make sure that you have selected the option for the right satellite
on the Point Dish/Signal menu.
on the Point Dish/Signal menu.
•
Make sure that the cable(s) for the satellite you have selected are
connected to the LNBF that receives signals from that satellite.
connected to the LNBF that receives signals from that satellite.
061
•
You may have set up the receiver
to accept a transmission (a
“download”) of the latest
operating software via the
satellite signal.
to accept a transmission (a
“download”) of the latest
operating software via the
satellite signal.
•
It is very important for the receiver to get the latest operating
software, so let the receiver do so. The “download” may take
several minutes. Do not disturb or unplug the receiver during
this time.
software, so let the receiver do so. The “download” may take
several minutes. Do not disturb or unplug the receiver during
this time.
Message Number
Possible Reason
What to Do