ATTO Technology 2700C Benutzerhandbuch
41
ATTO Technology Inc. iPBridge Installation and Operation Manual
6.1.3 Maintenance commands
The CLI commands outlined in this chapter may be used to get information or perform functions which
are used in a variety of situations with the ATTO iPBridge.
are used in a variety of situations with the ATTO iPBridge.
Date
Sets the date for the iPBridge if SNTP has been disabled
or is not available.
Sets the date for the iPBridge if SNTP has been disabled
or is not available.
Set syntax: set Date [MM] / [DD] / [YYYY]
Requires a SaveConfiguration command
Get syntax: get Date
Requires a SaveConfiguration command
Get syntax: get Date
FirmwareRestart
Causes the iPBridge to reboot, then re-initialize its
firmware.
Causes the iPBridge to reboot, then re-initialize its
firmware.
Immediate command: FirmwareRestart
MaxOpTemp
Establishes/reports the maximum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge rises above the maximum MaxOpTemp, thermal
control event handling occurs.
Valid entries are between 55 and 70 degrees C
Establishes/reports the maximum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge rises above the maximum MaxOpTemp, thermal
control event handling occurs.
Valid entries are between 55 and 70 degrees C
Default: 70
Set syntax: set MaxOpTemp [55-70]
Requires a SaveConfiguration command
Get syntax: get MaxOpTemp
Set syntax: set MaxOpTemp [55-70]
Requires a SaveConfiguration command
Get syntax: get MaxOpTemp
MinOpTemp
Establishes/reports the minimum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge falls below the minimum MinOpTemp, thermal
control event handling occurs. Valid entries are between
0 and 15 degrees
Establishes/reports the minimum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge falls below the minimum MinOpTemp, thermal
control event handling occurs. Valid entries are between
0 and 15 degrees
Default: 0
Set syntax: set MinOpTemp [0-15]
Requires a SaveConfiguration command
Get syntax: get MinOpTemp
Set syntax: set MinOpTemp [0-15]
Requires a SaveConfiguration command
Get syntax: get MinOpTemp
OpTempWarn
Controls the number of degrees in Celsius before a
thermal control event handling occurs. Warnings will be
made via system log entries. Valid entries are between 0
and 15 degrees
Controls the number of degrees in Celsius before a
thermal control event handling occurs. Warnings will be
made via system log entries. Valid entries are between 0
and 15 degrees
Default: 5
Set syntax: set OpTempWarn [0-15]
Requires a SaveConfiguration command
Get syntax: get OpTempWarn
Set syntax: set OpTempWarn [0-15]
Requires a SaveConfiguration command
Get syntax: get OpTempWarn
Password
RestoreConfiguration default sets the password to the
default value
Passwords are case sensitive, 1-32 characters with no
spaces
When the password is all 0s, TCP/IP and ftp do not
validate the password and MD5 authentication are
disabled.
RestoreConfiguration default sets the password to the
default value
Passwords are case sensitive, 1-32 characters with no
spaces
When the password is all 0s, TCP/IP and ftp do not
validate the password and MD5 authentication are
disabled.
Default: Password
Set syntax: set Password
Requires a SaveConfiguration command
Set syntax: set Password
Requires a SaveConfiguration command
Reserve
Reservation of the iPBridge is implicit: once the
configuration image is changed by any user of services,
the iPBridge becomes RESERVED. Executing a
SaveConfiguration or\ Restore configuration RELEASES
the iPBridge so that other services users may access it.
When iPBridge services interface is RESERVED, set
commands from other users are unavailable.
At least one interface must always have access to the
iPBridge.
Reservation of the iPBridge is implicit: once the
configuration image is changed by any user of services,
the iPBridge becomes RESERVED. Executing a
SaveConfiguration or\ Restore configuration RELEASES
the iPBridge so that other services users may access it.
When iPBridge services interface is RESERVED, set
commands from other users are unavailable.
At least one interface must always have access to the
iPBridge.
Immediate command: Reserve
RestoreConfiguration
Restores configuration to either the default configuration
or the configuration last saved into non-volatile memory.
The saved option will undo any changes made since the
last save.
Restores configuration to either the default configuration
or the configuration last saved into non-volatile memory.
The saved option will undo any changes made since the
last save.
Immediate command: RestoreConfiguration [Default |
Saved]
Saved]