ATTO Technology 2700C Benutzerhandbuch
42
Interfaces: CLI
SNTP
Controls the SNTP (Simple Network Time Protocol)
settings for the iPBridge. When enabled, the iPBridge
will try to contact a specified SNTP server at reset and
every 12 hours after to initialize/synchronize the time.
Controls the SNTP (Simple Network Time Protocol)
settings for the iPBridge. When enabled, the iPBridge
will try to contact a specified SNTP server at reset and
every 12 hours after to initialize/synchronize the time.
Default: Enabled
Set syntax: set SNTP [enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get SNTP
Set syntax: set SNTP [enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get SNTP
SNTPServer
Controls the IP address of the SNTP time server that the
iPBridge will contact to initialize/synchronize the time.
If the iPBridge is unable to contact the specified SNTP
server within 30 seconds, the iPBridge will try to contact
the first auxiliary SNTP time server. If the first auxiliary
SNTP time server is not available, the iPBridge will try to
contact the second auxiliary SNTP time server. If the
second auxiliary SNTP time server is not available, the
iPBridge will continue to approximate the time based on
the most recent SNTP time server, physical real time
clock or manual initialization/synchronization.
Controls the IP address of the SNTP time server that the
iPBridge will contact to initialize/synchronize the time.
If the iPBridge is unable to contact the specified SNTP
server within 30 seconds, the iPBridge will try to contact
the first auxiliary SNTP time server. If the first auxiliary
SNTP time server is not available, the iPBridge will try to
contact the second auxiliary SNTP time server. If the
second auxiliary SNTP time server is not available, the
iPBridge will continue to approximate the time based on
the most recent SNTP time server, physical real time
clock or manual initialization/synchronization.
Auxiliary time servers
129.6.15.28 (
129.6.15.28 (
www.time-a.nist.gov
)
132.163.4.101 (
www.time-a-timefreq.bidrdoc.gov
)
Default: 192.43.244.18 (
www.time.nist.gov
)
Set syntax: set SNTPServer [xxx.xxx.xxx.xxx]
Requires a SaveConfiguration command
Get syntax: get SNTPServer
Requires a SaveConfiguration command
Get syntax: get SNTPServer
SpeedWrite
When enabled, improves the performance of FCP WRITE
commands to Fibre Channel devices attached to the
iPBridge. Specify Fibre Channel fp for a specific Fibre
Channel port or fpidx, or all for a list of the Speedwrite
states of all currently mapped Fibre devices.
When enabled, improves the performance of FCP WRITE
commands to Fibre Channel devices attached to the
iPBridge. Specify Fibre Channel fp for a specific Fibre
Channel port or fpidx, or all for a list of the Speedwrite
states of all currently mapped Fibre devices.
Default: disabled
Set syntax: set SpeedWrite fc [fp | fcidx| all]
[enabled|disabled]
Get syntax: get SpeedWrite fc [fp | fcidx| all]
Set syntax: set SpeedWrite fc [fp | fcidx| all]
[enabled|disabled]
Get syntax: get SpeedWrite fc [fp | fcidx| all]
SpeedWriteDefault
When enabled, SpeedWrite performance enhancement is
set as the default for any subsequent Fibre Channel
devices mapped manually or via an AutoMap operation.
If disabled, the iPBridge will not attempt SpeedWrite
performance enhancement to newly-mapped Fibre
Channel devices.
When enabled, SpeedWrite performance enhancement is
set as the default for any subsequent Fibre Channel
devices mapped manually or via an AutoMap operation.
If disabled, the iPBridge will not attempt SpeedWrite
performance enhancement to newly-mapped Fibre
Channel devices.
Default: disabled
Set syntax: set SpeedWriteDefault [enabled | disabled]
Get syntax: get SpeedWriteDefault
Set syntax: set SpeedWriteDefault [enabled | disabled]
Get syntax: get SpeedWriteDefault
TailEventLog
Displays new events to the terminal during a serial or
Telnet session.Press <ESC> to exit tail mode.
Displays new events to the terminal during a serial or
Telnet session.Press <ESC> to exit tail mode.
Immediate command: TailEventLog
Time
Controls the time for the iPBridge if SNTP has been
disabled or is not available.
Controls the time for the iPBridge if SNTP has been
disabled or is not available.
Set syntax: set Time [HH]: [MM]: [SS]
Requires a SaveConfiguration command
Get syntax: get Time
Requires a SaveConfiguration command
Get syntax: get Time
TimeZone
Controls the time zone for the iPBridge if SNTP has been
disabled or is not available. Choices are EST, CST,
MST,
Controls the time zone for the iPBridge if SNTP has been
disabled or is not available. Choices are EST, CST,
MST,
.
PST or numerical offset from GMT in the form of
+/-:HH:MM.When SNTP is enabled, the iPBridge
applies the time zone setting to the time retrieved from a
specified SNTP time server to determine local time.
applies the time zone setting to the time retrieved from a
specified SNTP time server to determine local time.
Default: EST
Set syntax: set TimeZone [ [EST | CST | MST | PST] [+ /
- HH :MM ] ]
Requires a SaveConfiguration command
Get syntax: get TimeZone
Set syntax: set TimeZone [ [EST | CST | MST | PST] [+ /
- HH :MM ] ]
Requires a SaveConfiguration command
Get syntax: get TimeZone
Username
Specifies username for all TCP/IP, FTP and ExpressNAV
web server sessions.The username is case insensitive, 1-
32 characters, no spaces.
Specifies username for all TCP/IP, FTP and ExpressNAV
web server sessions.The username is case insensitive, 1-
32 characters, no spaces.
Changes to the Admin Level
Username will require an Admin Level password.
Default: root
Set syntax: set Username [username]
Requires a SaveConfiguration command
Get syntax: get Username
Set syntax: set Username [username]
Requires a SaveConfiguration command
Get syntax: get Username