ATTO Technology 2700C Benutzerhandbuch
44
Interfaces: CLI
DumpEventLog
Dumps the contents of the entire event log to an RS-232
or TCP/IP session (over Ethernet) without impact on the
log itself. (the log is not cleared). No events will be
recorded until the command has been completed.
Dumps the contents of the entire event log to an RS-232
or TCP/IP session (over Ethernet) without impact on the
log itself. (the log is not cleared). No events will be
recorded until the command has been completed.
Immediate command: DumpEventLog
DumpTraceLog
Dumps the contents of the entire trace log to an RS-232
or TCP/IP session (over Ethernet) without impact on the
log itself. (the log is not cleared). No events will be
recorded until the command has been completed.
Dumps the contents of the entire trace log to an RS-232
or TCP/IP session (over Ethernet) without impact on the
log itself. (the log is not cleared). No events will be
recorded until the command has been completed.
Immediate command: DumpTraceLog
EmailFromAddress
Configures the E-mail address that the bridge will use to
talk to the E-mail server. The E-mail address must be a
fully qualified Internet E-mail address, not more than 128
characters long.
Configures the E-mail address that the bridge will use to
talk to the E-mail server. The E-mail address must be a
fully qualified Internet E-mail address, not more than 128
characters long.
Immediate command: EmailFromAddress [full email
address]
address]
EmailNotify
Turns email notification on or off.
Turns email notification on or off.
Default: disabled.
Set syntax: set EmailNotify [enabled | disabled]
Get syntax: get EmailNotify
Set syntax: set EmailNotify [enabled | disabled]
Get syntax: get EmailNotify
EmailNotifyAddress
Configures notification addresses. Index is a number
between 1 and 5 includes. Full E-mail address is a
fully qualified Internet E-mail address, not more than 128
characters long. Warning level can be All, Warning,
Critical or None. None means no E-mails will be sent;
Critical means only critical severity events will engender
an E-mail; Warning means only warnings and critical
events will precipitate E-mail, and All means all
warnings, critical events and informational messages will
warrant an E-mail.
Configures notification addresses. Index is a number
between 1 and 5 includes. Full E-mail address is a
fully qualified Internet E-mail address, not more than 128
characters long. Warning level can be All, Warning,
Critical or None. None means no E-mails will be sent;
Critical means only critical severity events will engender
an E-mail; Warning means only warnings and critical
events will precipitate E-mail, and All means all
warnings, critical events and informational messages will
warrant an E-mail.
Set syntax: EmailNotifyAddress [index] [full email
address] [warning level]
Get syntax: EmailNotifyAddress < index | all >
address] [warning level]
Get syntax: EmailNotifyAddress < index | all >
EmailServerAddress
Configures the address of the server that the bridge must
contact in order to send out E-mail notifications.
Configures the address of the server that the bridge must
contact in order to send out E-mail notifications.
Immediate command: EmailServerAddress [IP address]
EventLog
When enabled, records various system events to the event
log.
When enabled, records various system events to the event
log.
Default: enabled
Set syntax: set EventLog [enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get EventLog
Set syntax: set EventLog [enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get EventLog
EventLogFilter
Filters the display of data for specific iPBridge
subsystems when in EventLog mode. If enabled for a
particular subsystem and level, that subsystem and level
will be masked when the command EventLog is issued.
Filters the display of data for specific iPBridge
subsystems when in EventLog mode. If enabled for a
particular subsystem and level, that subsystem and level
will be masked when the command EventLog is issued.
Subsystem entries
................
Log level entries
... ...
FC
.....................................
INFO
.......
ENET
................................
WARN
.......
NVRAM
..............................
CRIT
.......
PERF
.................................
FAIL
..... .
ECC
...................................
ALL
.......
ALL
.......
GEN
.......
HTTP
.......
iSCSI
Default: disabled
Set syntax: set EventLogFilter [subsystem] [level]
[enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get EventLogFilter [subsystem] [level]
Set syntax: set EventLogFilter [subsystem] [level]
[enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get EventLogFilter [subsystem] [level]
Help
Displays a list of available commands. If command name
is specified, displays detailed command-specific
information.
Displays a list of available commands. If command name
is specified, displays detailed command-specific
information.
Immediate command: Help <command name>
IdentifyBridge
Enabling this option causes the Fault LED on the front
panel of the iPBridge to blink until the parameter is
disabled.
Enabling this option causes the Fault LED on the front
panel of the iPBridge to blink until the parameter is
disabled.
Default: disabled
Set syntax: set IdentifyBridge [enabled|disabled]
Get syntax: get IdentifyBridge
Set syntax: set IdentifyBridge [enabled|disabled]
Get syntax: get IdentifyBridge
Info
Displays version numbers and other production
information for key components within the iPBridge
Displays version numbers and other production
information for key components within the iPBridge
Immediate command: Info