Autostart as-6070 tw User Manual
AS-6070 TW User Guide
P. 11
Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.
Turbo Mode
If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user
leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it
is shut down by remote control), then shut down the engine and set the System to Ready Mode.
To activate Turbo Mode, follow all steps of the Ready Mode routine:
If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user
leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it
is shut down by remote control), then shut down the engine and set the System to Ready Mode.
To activate Turbo Mode, follow all steps of the Ready Mode routine:
1.
Ensure that all the doors are closed and that the shifter is in the neutral position.
2.
With the engine already running, apply the parking brake and release the brake pedal.
Make sure to release the brake pedal.
Make sure to release the brake pedal.
3.
Within 20 sec. press
LOCK
,
UNLOCK
or
START/STOP
on the transmitter.
The parking lights will flash 3 times quickly and remain lit.
4.
Remove the key: the engine will go on running.
5.
Exit the vehicle and close the door.
6.
Press and hold either:
a.
a.
LOCK
to lock the doors and shut down the engine after 60 sec.;
b.
UNLOCK
to unlock the doors and shut down the engine after 60 sec.;
c.
START/STOP
to shut down the engine immediately, without affecting the doors
(this will by-pass Turbo Mode).
Valet Mode with the Valet Switch
When your vehicle is in Valet Mode, the remote starter functionalities are disabled. If the vehicle
needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being
remote-started accidentally.
When your vehicle is in Valet Mode, the remote starter functionalities are disabled. If the vehicle
needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being
remote-started accidentally.
To put the system i n t o Valet Mode:
1. Turn the ignition key to the
IGNITION ON (RUN)
position.
2. Within 3 sec., press the valet button (the L.E.D. will come
ON
solid).
To take the system o u t o f Valet Mode:
1. Turn the ignition key to the
IGNITION ON (RUN)
position.
2. Within 3 sec., press and release the valet button (the L.E.D. will come
OUT
).
Note: Once Valet Mode is activated, the remote starter and alarm functions will be disabled.
Ignition Valet
This feature will allow you to remotely put your system into Valet Mode by using the ignition key
instead of the Valet button as above. Ignition Valet can be used without a Valet button installed.
This feature will allow you to remotely put your system into Valet Mode by using the ignition key
instead of the Valet button as above. Ignition Valet can be used without a Valet button installed.
To put the system i n t o Valet Mode:
x Insert the ignition key into the ignition switch. Within 10 sec.,
turn the key 5 times successively into the
IGNITION ON / RUN
and
OFF
positions.
x The parking lights will flash three times to indicate that the vehicle is now in Valet Mode.
The L.E.D. will come
ON
solid.
To take the system o u t o f Valet Mode:
x Insert the ignition key into the ignition switch. Within 10 sec.,
turn the key 5 times successively into the
IGNITION ON / RUN
and
OFF
positions.
x The parking lights will flash twice to indicate that the vehicle is now in Valet Mode.
The L.E.D. will go out.
Note: With the Remote Valet activated, the remote starter and alarm functions will be disabled.
Start Attempts Indicator (Valet Mode)
This reveals start attempts made while the vehicle was in Valet Mode. The parking lights will:
This reveals start attempts made while the vehicle was in Valet Mode. The parking lights will: