Atmel Evaluation Kit AT91SAM9X25-EK AT91SAM9X25-EK Data Sheet
Product codes
AT91SAM9X25-EK
540
SAM9X25 [DATASHEET]
11054E–ATARM–10-Mar-2014
for( i=1; i<=((AT91C_BASE_UDPHS->UDPHS_IPFEATURES &
AT91C_UDPHS_DMA_CHANNEL_NBR)>>4); i++ ) {
// RESET endpoint canal DMA:
// DMA stop channel command
AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMACONTROL = 0; // STOP
command
// Disable endpoint
AT91C_BASE_UDPHS->UDPHS_EPT[i].UDPHS_EPTCTLDIS |= 0XFFFFFFFF;
// Reset endpoint config
AT91C_BASE_UDPHS->UDPHS_EPT[i].UDPHS_EPTCTLCFG = 0;
// Reset DMA channel (Buff count and Control field)
AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMACONTROL = 0x02; // NON
STOP command
// Reset DMA channel 0 (STOP)
AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMACONTROL = 0; // STOP
command
// Clear DMA channel status (read the register for clear it)
AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMASTATUS =
AT91C_BASE_UDPHS->UDPHS_DMA[i].UDPHS_DMASTATUS;
}
32.6.10 Handling Transactions with USB V2.0 Device Peripheral
32.6.10.1 Setup Transaction
The setup packet is valid in the DPR while RX_SETUP is set. Once RX_SETUP is cleared by the application, the
UDPHS accepts the next packets sent over the device endpoint.
UDPHS accepts the next packets sent over the device endpoint.
When a valid setup packet is accepted by the UDPHS:
The UDPHS device automatically acknowledges the setup packet (sends an ACK response)
Payload data is written in the endpoint
Sets the RX_SETUP interrupt
The BYTE_COUNT field in the UDPHS_EPTSTAx register is updated
An endpoint interrupt is generated while RX_SETUP in the UDPHS_EPTSTAx register is not cleared. This interrupt is
carried out to the microcontroller if interrupts are enabled for this endpoint.
carried out to the microcontroller if interrupts are enabled for this endpoint.
Thus, firmware must detect RX_SETUP polling UDPHS_EPTSTAx or catching an interrupt, read the setup packet in the
FIFO, then clear the RX_SETUP bit in the UDPHS_EPTCLRSTA register to acknowledge the setup stage.
FIFO, then clear the RX_SETUP bit in the UDPHS_EPTCLRSTA register to acknowledge the setup stage.
If STALL_SNT was set to 1, then this bit is automatically reset when a setup token is detected by the device. Then, the
device still accepts the setup stage. (See
device still accepts the setup stage. (See
32.6.10.2 NYET
NYET is a High Speed only handshake. It is returned by a High Speed endpoint as part of the PING protocol.
High Speed devices must support an improved NAK mechanism for Bulk OUT and control endpoints (except setup
stage). This mechanism allows the device to tell the host whether it has sufficient endpoint space for the next OUT
transfer (see USB 2.0 spec 8.5.1 NAK Limiting via Ping Flow Control).
stage). This mechanism allows the device to tell the host whether it has sufficient endpoint space for the next OUT
transfer (see USB 2.0 spec 8.5.1 NAK Limiting via Ping Flow Control).
The NYET/ACK response to a High Speed Bulk OUT transfer and the PING response are automatically handled by
hardware in the UDPHS_EPTCTLx register (except when the user wants to force a NAK response by using the
NYET_DIS bit).
hardware in the UDPHS_EPTCTLx register (except when the user wants to force a NAK response by using the
NYET_DIS bit).
If the endpoint responds instead to the OUT/DATA transaction with an NYET handshake, this means that the endpoint
accepted the data but does not have room for another data payload. The host controller must return to using a PING
token until the endpoint indicates it has space available.
accepted the data but does not have room for another data payload. The host controller must return to using a PING
token until the endpoint indicates it has space available.