Atmel Evaluation Kit AT91SAM9M10-G45-EK AT91SAM9M10-G45-EK Data Sheet
Product codes
AT91SAM9M10-G45-EK
421
SAM9M10 [DATASHEET]
6355F–ATARM–12-Mar-13
29.5.3.3
Transmitter Control
When the transmitter is enabled, the bit TXRDY (Transmitter Ready) is set in the status register DBGU_SR. The
transmission starts when the programmer writes in the Transmit Holding Register DBGU_THR, and after the writ-
ten character is transferred from DBGU_THR to the Shift Register. The bit TXRDY remains high until a second
character is written in DBGU_THR. As soon as the first character is completed, the last character written in
DBGU_THR is transferred into the shift register and TXRDY rises again, showing that the holding register is empty.
transmission starts when the programmer writes in the Transmit Holding Register DBGU_THR, and after the writ-
ten character is transferred from DBGU_THR to the Shift Register. The bit TXRDY remains high until a second
character is written in DBGU_THR. As soon as the first character is completed, the last character written in
DBGU_THR is transferred into the shift register and TXRDY rises again, showing that the holding register is empty.
When both the Shift Register and the DBGU_THR are empty, i.e., all the characters written in DBGU_THR have
been processed, the bit TXEMPTY rises after the last stop bit has been completed.
been processed, the bit TXEMPTY rises after the last stop bit has been completed.
Figure 29-11.
Transmitter Control
29.5.4
Peripheral Data Controller
Both the receiver and the transmitter of the Debug Unit's UART are generally connected to a Peripheral Data Con-
troller (PDC) channel.
troller (PDC) channel.
The peripheral data controller channels are programmed via registers that are mapped within the Debug Unit user
interface from the offset 0x100. The status bits are reported in the Debug Unit status register DBGU_SR and can
generate an interrupt.
interface from the offset 0x100. The status bits are reported in the Debug Unit status register DBGU_SR and can
generate an interrupt.
The RXRDY bit triggers the PDC channel data transfer of the receiver. This results in a read of the data in
DBGU_RHR. The TXRDY bit triggers the PDC channel data transfer of the transmitter. This results in a write of a
data in DBGU_THR.
DBGU_RHR. The TXRDY bit triggers the PDC channel data transfer of the transmitter. This results in a write of a
data in DBGU_THR.
29.5.5
Test Modes
The Debug Unit supports three tests modes. These modes of operation are programmed by using the field
CHMODE (Channel Mode) in the mode register DBGU_MR.
CHMODE (Channel Mode) in the mode register DBGU_MR.
The Automatic Echo mode allows bit-by-bit retransmission. When a bit is received on the DRXD line, it is sent to
the DTXD line. The transmitter operates normally, but has no effect on the DTXD line.
the DTXD line. The transmitter operates normally, but has no effect on the DTXD line.
The Local Loopback mode allows the transmitted characters to be received. DTXD and DRXD pins are not used
and the output of the transmitter is internally connected to the input of the receiver. The DRXD pin level has no
effect and the DTXD line is held high, as in idle state.
and the output of the transmitter is internally connected to the input of the receiver. The DRXD pin level has no
effect and the DTXD line is held high, as in idle state.
The Remote Loopback mode directly connects the DRXD pin to the DTXD line. The transmitter and the receiver
are disabled and have no effect. This mode allows a bit-by-bit retransmission.
are disabled and have no effect. This mode allows a bit-by-bit retransmission.
DBGU_THR
Shift Register
DTXD
TXRDY
TXEMPTY
Data 0
Data 1
Data 0
Data 0
Data 1
Data 1
S
S
P
P
Write Data 0
in DBGU_THR
Write Data 1
in DBGU_THR
stop
stop