Delta Tau TURBO CLIPPER DRIVE User Manual
Turbo Clipper Drive User Manual
Specification
8
SPECIFICATIONS
Part Number
Delta Tau Assembly Numbers (top to bottom):
Control Board (Clipper)
603871
Breakout Board
603926
Power Board
603925
Turbo Clipper Drive (Control+Breakout+Power)
Clipper & Breakout only (Control+Breakout, without Power)
CD
0
0 0
1
0
C
4
-
-
-
0
4
0
0
0 0
T
CPU Options - Turbo PMAC 2 Processor
C0 - 80Mhz, 8Kx24 Internal, 256Kx24SRAM, 1MB Flash (Default)
C3 - 80Mhz, 8Kx24 Internal, 1Mx24SRAM, 4MB Flash
F3 - 240Mhz, 192Kx24 Internal, 1Mx24SRAM, 4MB Flash
C3 - 80Mhz, 8Kx24 Internal, 1Mx24SRAM, 4MB Flash
F3 - 240Mhz, 192Kx24 Internal, 1Mx24SRAM, 4MB Flash
B
G
L
B
Turbo Clipper Drive Number Definition
Communication Options
TCD X - XX - XXX
– X?X - XXXX
USB2 and Eth100 are included
Note: To use PMAC-NC software, DPRAM is required
0 - No Options, Default
D - (Clipper OPT-2) DPRAM option, size 8K x 16-bit wide
M - (Clipper Opt-15M) ModBus Ethernet Communication Protocol(Software) option
S - (Clipper OPT-2 and Opt-15M) DPRAM and Modbus Options Combined
D - (Clipper OPT-2) DPRAM option, size 8K x 16-bit wide
M - (Clipper Opt-15M) ModBus Ethernet Communication Protocol(Software) option
S - (Clipper OPT-2 and Opt-15M) DPRAM and Modbus Options Combined
G
00 - No Additional* Options
xx - Factory assigned digits for Additional* Options
xx - Factory assigned digits for Additional* Options
Factory Assigned Options
K
L
* If Opt. 10xx (specific firmware version) or any other Additional Option
is required, contact factory for digits
K
and
L
(Factory Assigned digits).
If Opt. 10xx is not ordered the latest firmware is used.
Other Options
0 - No Options (Default)
1 - Opt. 11A HI-Speed Dig. Out
0 - No Options (Default)
1 - Opt. 11A HI-Speed Dig. Out
PWM Laser Control
J
K
J
-
B B
0
0 5
0
0
C
2
-
-
-
0
4
0
1
0 0
C
CPU Options - Turbo PMAC 2 Processor
C0 - 80Mhz, 8Kx24 Internal, 256Kx24SRAM, 1MB Flash (Default)
C3 - 80Mhz, 8Kx24 Internal, 1Mx24SRAM, 4MB Flash
F3 - 240Mhz, 192Kx24 Internal, 1Mx24SRAM, 4MB Flash
C3 - 80Mhz, 8Kx24 Internal, 1Mx24SRAM, 4MB Flash
F3 - 240Mhz, 192Kx24 Internal, 1Mx24SRAM, 4MB Flash
B
G
L
B
Clipper with Breakout Board Part Number Definition
Communication Options
CBB X - XX - XXX
– X?X - XXXX
USB2 and Eth100 are included
Note: To use PMAC-NC software, DPRAM is required
0 - No Options, Default
D - (Clipper OPT-2) DPRAM option, size 8K x 16-bit wide
M - (Clipper Opt-15M) ModBus Ethernet Communication Protocol(Software) option
S - (Clipper OPT-2 and Opt-15M) DPRAM and Modbus Options Combined
D - (Clipper OPT-2) DPRAM option, size 8K x 16-bit wide
M - (Clipper Opt-15M) ModBus Ethernet Communication Protocol(Software) option
S - (Clipper OPT-2 and Opt-15M) DPRAM and Modbus Options Combined
G
00 - No Additional* Options
xx - Factory assigned digits for Additional* Options
xx - Factory assigned digits for Additional* Options
Factory Assigned Options
K
L
* If Opt. 10xx (specific firmware version) or any other Additional Option is required, contact factory for digits
K
and
L
(Factory Assigned digits).
If Opt. 10xx is not ordered the latest firmware is used.
0 - No Options (Default)
1 - Opt. 11A HI-Speed Dig. Out
1 - Opt. 11A HI-Speed Dig. Out
PWM Laser Control
J
K
J
-
H
0 - No Options (Default)
1 - Opt. 12 2-channels 12-bit A/D converter & 1 12-bit
D/A converter
1 - Opt. 12 2-channels 12-bit A/D converter & 1 12-bit
D/A converter
H
Other Options