Whirlpool T-K1S User Manual
20
Optional Items
1. TKRE01emperature Remote Controller
The TKRE01
temperature Remote
Controller has two
functions, it allows the
output temperature
from the T-K1S to be
adjusted within the
range of 95 °F to 167
temperature Remote
Controller has two
functions, it allows the
output temperature
from the T-K1S to be
adjusted within the
range of 95 °F to 167
°F, and it also works as a diagnostic tool that will
give a concise error code whenever there is a
problem with the unit. The temperature options
are 95°F, 100°F, 102°F, 104°F, 106°F, 108°F,
109°F, 111°F, 113°F, 115°F, 117°F, 122°F,
131°F, 140°F, 158°F, and 167°F. See the trouble
shooting section for information on possible error
codes.
give a concise error code whenever there is a
problem with the unit. The temperature options
are 95°F, 100°F, 102°F, 104°F, 106°F, 108°F,
109°F, 111°F, 113°F, 115°F, 117°F, 122°F,
131°F, 140°F, 158°F, and 167°F. See the trouble
shooting section for information on possible error
codes.
3. TK-TV03 Vent Damper
The TK-TV03 Vent
Damper prevents the
backflow of air
through the exhaust
vent. This is CSA
approved part of the
Damper prevents the
backflow of air
through the exhaust
vent. This is CSA
approved part of the
unit. This helps prevent harmful exhaust gases
from entering the home, as well as helping to
prevent the units from freezing in areas where
cold air can be blown into the exhaust system.
Install vent damper according to manufacturer’s
installation instruction, and any applicable codes.
from entering the home, as well as helping to
prevent the units from freezing in areas where
cold air can be blown into the exhaust system.
Install vent damper according to manufacturer’s
installation instruction, and any applicable codes.
3. TK-TV01 Vent Terminator
This terminator can be used
where a T-K1S is going to be
vented out through a wall. This
is a CSA approved part of the
unit. Connect a Category III
Stainless vent pipe from the
where a T-K1S is going to be
vented out through a wall. This
is a CSA approved part of the
unit. Connect a Category III
Stainless vent pipe from the
top of the unit to the backside of this terminator to
exhaust flue gases through the wall without a
thimble. Install vent terminator in accordance with
manufacturer’s installation instructions and any
applicable local codes.
exhaust flue gases through the wall without a
thimble. Install vent terminator in accordance with
manufacturer’s installation instructions and any
applicable local codes.
4. TK-TV03 Vent Cap
The TK-TV03 Vent Cap is for
outdoor installation with the
T-K1S water heater. The cap
is installed on the top of the
unit, instead of connecting an
exhaust vent. The cap will
prevent any debris that might
be in the environment from entering the unit and
causing damage or a fire hazard, as well as
preventing rain or other weather from entering the
unit.
causing damage or a fire hazard, as well as
preventing rain or other weather from entering the
unit.
5. TK-BK01 Wall Mounting Brackets
The TK-BK01 Wall Mounting Brackets allow the T-K1S to be installed
hanging from a wall. It is not necessary to earthquake strap these
heaters if these brackets are used. If the unit is not going to be
mounted on a wall, the “L” brackets that are included with every unit
will be sufficient as earthquake protection. Install unit and brackets
according to manufacturer’s installation instructions and any
applicable codes.
hanging from a wall. It is not necessary to earthquake strap these
heaters if these brackets are used. If the unit is not going to be
mounted on a wall, the “L” brackets that are included with every unit
will be sufficient as earthquake protection. Install unit and brackets
according to manufacturer’s installation instructions and any
applicable codes.