Lynx L36ASRLP Owner's Manual

Keep threading compound

off of the first two pipe

Keep thr

Keep threading compound

eading compound

threads to avoid having

off of the first two pipe

any small pieces of

threads to avoid having

compound break loose and

any small pieces of

clog a burner valve or

compound break loose and

orifice. Do not use

clog a burner valve or

threading compound on

any flare fittings

threading compound on

for

built-in installations, it is rec-

ommended that any flexible

pipe used be kept as short

as possible.

pipe used be kept as short

(see indeX: “gas

connections” for typical permanent

hook up.)

for

freestanding

units using

freestanding

natural gas, lynx str

ongly

recommends using a quick

disconnect kit.

recommends using a quick

, is available from your dealer

lp gas

grills set up for lp gas come

equipped with an LP hose/

rills set up for

regulator assembly for con-

equipped with an LP hose/

nection to a standard 20 lb. lp

cylinder. (Type 1). All fittings

necessary to attach the

cylinder. (Type 1). All fittings

assembly to the grill are

included.

Keep

last two

Keep

threads

clean

connection

permanently plumbed lp con-

nections, such as those in line

ermanently plumbed

with a bulk cylinder, require

with a bulk cylinder

a 4/11 regulator. (lynx

, require

30781)

when using the 4/11 regulator

you must ensure that it is set for

the proper fuel type. this is done

by removing the regulator cap and

gasket and looking at the bottom

of the plunger to see what fuel

type is visible. this is the regulator

fuel setting. nat is for natural gas

nat

and lp is for propane gas. the lp

setting can be further identified

by the large diameter disk on the

bottom of the plunger. to change

from one gas to the other simply

push the plunger to the side to

snap it out of the cap, turn the

plunger so it reads the desired gas

type on the bottom, and push the

plunger until it snaps back into

place in the cap then replace the

cap into the regulator.

gas line to the grill.

warning

Do not change the regulator/hose

assembly or use any other assembly

than the one supplied with your

Lynx grill.

than the one supplied with your

Do not attempt to use a 5LP-A

equipped regulator/hose assembly

Do not attempt to use a 5LP-A

with a standard 510 POL cylinder/

equipped regulator/hose assembly

valve assembly.
Do not store a spare LP-gas cylinder

under or near this appliance

Do not store a spare LP-gas cylinder

Never fill the cylinder beyond 80

percent full

Never fill the cylinder beyond 80

If the information above is not

followed exactly, a fire causing

death or serious injury may occur.

lp cylinder

requirements

the lp cylinder must be con-

structed and marked in accor-

dance with the specifications

for

dance with the specifications

lp gas cylinders of the

dance with the specifications

u.s

dance with the specifications

department of

gas cylinders of the

transportation

(dot

epartment of

) and designed for use

epartment of

epartment of ransportation

ransportation

with a type 1 system only

cylinders of free standing

grills must be secured using

the provided cylinder

retention system to avoid

the provided cylinder

accidental movement.

cylinder for a refill, exchange

only for a

cylinder for a refill, exchange

type 1 20lb cylinder

with an over

ype 1 20lb cylinder

-fill protection

ype 1 20lb cylinder

with an over

ype 1 20lb cylinder

device.
never use a cylinder with a

damaged valve.
a dented or rusty lp cylinder

may be hazardous and should

be avoided. if in doubt, have

may be hazardous and should

it checked by your lp supplier.
always check for leaks after

every lp cylinder change.

(see indeX: “leak test” for further

details.)

always shut off the lp-gas

supply at the cylinder when

the grill is not in use.

supply at the cylinder when

cylinders must be stored

outdoors in a well-venti-

lated area out of the reach of

children. if your grill is stored

indoors, the lp cylinder must

be stored outside.