Perlick HA24BB31L Use & Care Manual
5
perlick.com
PERLICK RESIDENTIAL INSTALLATION MANUAL
To Set Target Temperature
Press and release the SET button. Display will show the current
temperature setpoint.
Press and release the SET button. Display will show the current
temperature setpoint.
To Change Setpoint Temperature
1. Press and hold the SET button until the display shows the
current setpoint temperature with the “F” flashing.
2. Use the UP and DOWN arrow button to scroll to the desired
temperature.
NOTE: Dependent on the model and configuration, the controllers
have been programmed to only allow a temperature adjustment
within a specified range. See the chart below for the specified range
allowed for your unit.
have been programmed to only allow a temperature adjustment
within a specified range. See the chart below for the specified range
allowed for your unit.
Signature Series 15”, 24” Single-Zone and Sottile, and 48” ,
ADA Freezer Control Instructions
ADA Freezer Control Instructions
Dual-Zone Temperature Scale
To change F to C, press and hold the down arrow for 3 seconds.
To change F to C, press and hold the down arrow for 3 seconds.
To Start A Manual Defrost (Freezer Models Only)
Press the DEFROST button (melting snowflake)
Press the DEFROST button (melting snowflake)
To Set Maximum Stored Temperature
Press the UP arrow button to see the maximum stored
temperature. To reset the maximum stored temperature, while
displayed, press and hold the SET button until ‘rst’ flashes in the
display.
Press the UP arrow button to see the maximum stored
temperature. To reset the maximum stored temperature, while
displayed, press and hold the SET button until ‘rst’ flashes in the
display.
To Set Minimum Stored Temperature
Press the DOWN arrow button to see the minimum stored
temperature. To reset the minimum stored temperature, while
displayed, press and hold the SET button until ‘rst’ flashes in the
display.
Press the DOWN arrow button to see the minimum stored
temperature. To reset the minimum stored temperature, while
displayed, press and hold the SET button until ‘rst’ flashes in the
display.
On/Off
Press the ON/OFF button to turn the unit on or off.
Press the ON/OFF button to turn the unit on or off.
Key Combinations:
+
Press the UP and DOWN arrow
buttons to lock and unlock the
keyboard
buttons to lock and unlock the
keyboard
+
Press the SET and DOWN arrow
buttons simultaneously to enter
programming mode.
buttons simultaneously to enter
programming mode.
+
Press the SET and UP arrow buttons
simultaneously to return to room
temperature display.
simultaneously to return to room
temperature display.
Signature Series – Dual-Zone Units
Model
Range (F)
HP24D
Upper 51° - 65° / Lower 45° - 60°
NOTE: Dependent on the model and configuration, the controllers
have been programmed to only allow a temperature adjustment
within a specified range. See the chart below for the specified range
allowed for your unit.
have been programmed to only allow a temperature adjustment
within a specified range. See the chart below for the specified range
allowed for your unit.
Signature Series – HP15 Models
Model
Min Temp Set
Max Temp Set
HP15R
33° F
42° F
HP15B
33° F
48° F
HP15W
45° F
65° F
HP15T
33° F
42° F
Signature Series – HP24 Models
Model
Min Temp Set
Max Temp Set
HP24R
33° F
42° F
HP24F
-10° F
10° F
HP24B
33° F
48° F
HP24W
45° F
65° F
HP24T
33° F
42° F
Signature Series – HP48 Models
Model
Min Temp Set
Max Temp Set
HP48WO
40° F
65° F
HP48WW
40° F
65° F
Signature Series Sottile
Model
Min Temp Set
Max Temp Set
HH24RS
33°
42°
HH24BS
33°
48°
HH24WS
45°
65°
ADA-Compliant Series
Model
Min Temp Set
Max Temp Set
HA24FB
-10°
10
LED Functions
The following table describes LED functions
The following table describes LED functions
LED
Mode
Function
ON
Compressor is on
Flashing
Anti-short cycle
delay is on
ON
Defrost is on
ON
Alarm is on
Flashing
You are in the process of
programming the unit