Perlick HA24BB31L Use & Care Manual
PERLICK RESIDENTIAL INSTALLATION MANUAL
6
perlick.com
LED Functions
The following table describes LED Funtions
The following table describes LED Funtions
DIGITAL TEMPERATURE CONTROL
C-Series Models
Figure 2. nEW 961 Digital Temperature Controller
To Change Setpoint Temperature
1. Press
1. Press
. “SP” will be displayed. Press
again to display
current setpoint temperature.
2. Press
2. Press
and to modify it and
or to save the
change.
On/Off
To turn the unit off, press and hold for at least 5 seconds.
“OF” will be displayed. To turn the unit on again, press and hold
To turn the unit off, press and hold for at least 5 seconds.
“OF” will be displayed. To turn the unit on again, press and hold
for at least 5 seconds.
Perlick C-Series units come standard with digital control.
Programming Button Definitions:
Defrost LED
Permanently on: defrost active
Flashing: manual defrost active
Off: otherwise
Permanently on: defrost active
Flashing: manual defrost active
Off: otherwise
Alarm LED
Permanently on: alarm active
Flashing: alarm acknowledged
Off: otherwise
Permanently on: alarm active
Flashing: alarm acknowledged
Off: otherwise
Evaporator LED
Permanently on: fans active
Off: otherwise
Permanently on: fans active
Off: otherwise
Compressor LED
Permanently on: compressor active
Flashing: a delay, a protection or a
locked start-up
Off: otherwise
Permanently on: compressor active
Flashing: a delay, a protection or a
locked start-up
Off: otherwise
Aux LED
Permanently on: Aux output
active
Off: otherwise
Permanently on: Aux output
active
Off: otherwise
°C LED
Permanently on: display the
temperature
Off: otherwise
Permanently on: display the
temperature
Off: otherwise
STAND-BY (ESC)
Press and release
• Returns to the previous
menu level
• Confirms parameter value
Press for at least 5 sec.
• Activates the Standby
function (off ) (When
outside the menus)
outside the menus)
SET (ENTER)
Press and release
• Opens Machine Status menu
and displays alarms (if active)
Press for at least 5 sec.
• Opens Programming menu
• Confirm commands
• Confirm commands
UP
Press and release
• Scroll menu items
• Increases values
• Increases values
Press for at least 5 sec.
• Activates the Manual
Defrost function
DOWN
Press and release
• Scroll menu items
• Decreases values
• Decreases values
Press for at least 5 sec.
• Function can be configured
by the user
NOTE: Dependent on the model and configuration, the controllers
have been programmed to only allow a temperature adjustment
within a specified range. See the chart below for the specified range
allowed for your unit.
have been programmed to only allow a temperature adjustment
within a specified range. See the chart below for the specified range
allowed for your unit.
NOTE: When switched on, the device performs a Lamp Test; the
display and LEDs will flash for several seconds to check that they all
function correctly.
display and LEDs will flash for several seconds to check that they all
function correctly.
C-Series Models
Model
Temp Range
HC24R
33° - 42° F
HA24BB
33° - 48° F
HA24WB
45° - 65° F
DIAL TEMPERATURE CONTROL
ADA-Compliant Models
(Excludes ADA Freezer - HA24F models use digital controller found
on page 5)
ADA-Compliant Models
(Excludes ADA Freezer - HA24F models use digital controller found
on page 5)
C
O
O
LE
R
OFF
1
2
3
4
5
6
COLD
Figure 3. Dial Temperature Controller
Use a straight slot screwdriver to adjust the dial temperature
control. The control is located at the top rear panel of the
cabinet. Approximate temperature ranges are as follows:
control. The control is located at the top rear panel of the
cabinet. Approximate temperature ranges are as follows:
ADA-Compliant Series
Model
Temp Range
HA24RB
33° - 42° F
HA24BB
35° - 48° F
HA24WB
45° - 65° F