Lynx LPZAF Owner's Manual
NAPOLI PIZZA OVENS CARE & USE/INSTALLATION
|
27
This Quick Disconnect kit, part #LQD, is available
from your dealer.
from your dealer.
LP GAS
Ovens set up for LP gas come equipped with an LP hose/
regulator assembly for connection to a standard 20 lb.
LP cylinder. (Type 1). All fittings necessary to attach the
assembly to the oven are included.
regulator assembly for connection to a standard 20 lb.
LP cylinder. (Type 1). All fittings necessary to attach the
assembly to the oven are included.
Permanently plumbed LP connections, such as those in
line with a bulk cylinder, require a 4/11 regulator. (Lynx P/N
30781)
line with a bulk cylinder, require a 4/11 regulator. (Lynx P/N
30781)
When using the 4/11 regulator you must ensure that it is
set for the proper fuel type. This is done by removing the
regulator cap and gasket and looking at the bottom of the
plunger to see what fuel type is visible. This is the regulator
fuel setting. NAT is for natural gas and LP is for propane
gas. The LP setting can be further identified by the large
diameter disk on the bottom of the plunger. To change
from one gas to the other simply push the plunger to the
side to snap it out of the cap, turn the plunger so it reads
the desired gas type on the bottom, and push the plunger
until it snaps back into place in the cap then replace the
cap into the regulator.
set for the proper fuel type. This is done by removing the
regulator cap and gasket and looking at the bottom of the
plunger to see what fuel type is visible. This is the regulator
fuel setting. NAT is for natural gas and LP is for propane
gas. The LP setting can be further identified by the large
diameter disk on the bottom of the plunger. To change
from one gas to the other simply push the plunger to the
side to snap it out of the cap, turn the plunger so it reads
the desired gas type on the bottom, and push the plunger
until it snaps back into place in the cap then replace the
cap into the regulator.
Never connect an unregulated gas line to the oven.
LP Cylinder Requirements
The LP cylinder must be constructed and marked in
accordance with the specifications for LP gas cylinders of
the U.S. Department of Transportation (DOT) and designed
for use with a Type 1 system only.
accordance with the specifications for LP gas cylinders of
the U.S. Department of Transportation (DOT) and designed
for use with a Type 1 system only.
Cylinders of free standing ovens must be secured using
the provided cylinder retention system to avoid accidental
movement.
the provided cylinder retention system to avoid accidental
movement.
When exchanging
your cylinder for a
refill, exchange only
for a Type 1 20lb
cylinder with an over-fill
protection device.
your cylinder for a
refill, exchange only
for a Type 1 20lb
cylinder with an over-fill
protection device.
Never use a cylinder with a damaged valve.
A dented or rusty LP cylinder may be hazardous and
should be avoided. If in doubt, have it checked by your LP
supplier.
should be avoided. If in doubt, have it checked by your LP
supplier.
Always check for leaks after every LP cylinder change. (See
INDEX: “Leak Test” for further details.)
INDEX: “Leak Test” for further details.)
Always shut off the LP-gas supply at the cylinder when the
oven is not in use.
oven is not in use.
Cylinders must be stored outdoors in a well-ventilated area
out of the reach of children. If your oven is stored indoors,
the LP cylinder must be stored outside.
out of the reach of children. If your oven is stored indoors,
the LP cylinder must be stored outside.
LP cylinder with type 1 valve connection
GAS CONNECTIONS
...continued
Do not change the regulator/hose assembly or
use any other assembly than the one supplied with
your Lynx oven.
Do not attempt to use a 5LP-A equipped
Do not attempt to use a 5LP-A equipped
regulator/hose assembly with a standard 510 POL
cylinder/valve assembly.
Do not store a spare LP-gas cylinder under or near
Do not store a spare LP-gas cylinder under or near
this appliance.
Never fill the cylinder beyond 80 percent full.
If the information above is not followed exactly, a
Never fill the cylinder beyond 80 percent full.
If the information above is not followed exactly, a
fire causing death or serious injury may occur.
WARNING