Crown Audio I-T5000 HD Manuel D’Utilisation

DHCP: Turn an Encoder knob to turn DHCP on or off, then press the knob to 
confi rm your selection. With DHCP enabled, the IP address of the amplifi er 
might change at power-up. See System Architect Help fi les  for more 
information on DHCP.

DHCP: (caution! Dynamic IP)      

DHCP: (caution! Dynamic IP)      

   

   

Changes IP at powerUp

Changes IP at powerUp

      

      

OFF

IP Address: You set the IP address of the amplifi er here. See Section 9.1 for 
more information on IP Address. This function is disabled when DHCP is 
enabled.
1. Press an Encoder knob to access the left three digits, then turn the knob to 
set the number. 
2. Press again to access the middle three digits, then turn the knob to set the 
number. 
3. Press again to access the next digit to the right, then turn the knob to set the 
number.  
4. Press again to access the right-most digit, then turn the knob to set the 
number. 
5. Press again to save the IP address.

IP Address      

IP Address      

   

  

Turn to Set-Press to Save

Turn to Set-Press to Save

     

     

Subnet Mask: You set the Subnet Mask of the amplifi er here.  See Section 9.1 
for more information on Subnet Mask. This function is disabled when DHCP is 
enabled.
1. Press an Encoder knob to access the left three digits, then turn the knob to 
set the number. 
2. Press again to access the middle three digits, then turn the knob to set the 
number. 
3. Press again to access the next digit to the right, then turn the knob to set the 
number.  
4. Press again to access the right-most digit, then turn the knob to set the 
number. 
5. Press again to save the Subnet Mask.

Subnet Mask      

Subnet Mask      

   

   

Turn to Set-Press to Save

Turn to Set-Press to Save

     

     

4.2.7 COBRANET MENU
To access the CobraNet Menu from the Attenuation screen, press an Encoder 
knob, then press Prev.  This menu has selections for setting CobraNet 
parameters. Press an Encoder knob to access the CobraNet Menu selections. 
See Section 9.2 and the System Architect Help fi les for more on CobraNet.

Cobranet Menu

Cobranet Menu      

Cobranet Menu      

   

   

Push knob for cnet. menu

CobraNet Information: This screen displays information about the 
CobraNet network: The fi rmware version, ethernet status (down or up), and 
conductor priority. 

Cobranet Information      

Cobranet Information      

   

   

Ethernet Status:   UP      

Ethernet Status:   UP      

Conductor Priority: 

Conductor Priority: 

32

32

      

      

Firmware Version: 

Firmware Version: 

2.11.6

2.11.6

      

      

Ch1 CobraNet Rx: Turn the left Encoder knob to set the number of the RxA 
Bundle for Channel 1. Turn the right Encoder knob to set the CobraNet input for 
Channel 1. The word “Active” appears if there is audio on the bundle. Bundles 
1-8 are available at 48 kHz sampling rate, and bundles 1-4 are available at 96 
kHz sampling rate.

0

Ch1 Cobranet Rx      

Ch1 Cobranet Rx      

   

   

RxA Bundle

RxA Bundle

      

      

Cnet Input

Cnet Input

      

      

Ch2 CobraNet Rx: Turn the left Encoder knob to set the number of the RxA 
Bundle for Channel 1. Turn the right Encoder knob to set the CobraNet input for 
Channel 2. The word “Active” appears if there is audio on the bundle. Bundles 
1-8 are available at 48 kHz sampling rate, and bundles 1-4 are available at 96 
kHz sampling rate.

0

Ch2 Cobranet Rx      

Ch2 Cobranet Rx      

   

   

RxB Bundle

RxB Bundle

      

      

Cnet Input

Cnet Input

      

      

CobraNet Tx: Turn the left Encoder knob to set the number of the TxA Bundle 
for Channel 1. Turn the right Encoder knob to set the TxA position for Channel 
2. 

0

Cobranet Tx Bundles      

Cobranet Tx Bundles      

   

   

TxA (ch1)

TxA (ch1)      

      

TxB (ch2)

TxB (ch2)      

      

0

CobraNet Conductor Priority: Turn an Encoder knob to set the priority 
number of the CobraNet channel. Press the knob to confi rm your choice. See 
Section 9.2 for more on CobraNet conductor priority.

Cobranet Conductor Priority      

Cobranet Conductor Priority      

   

   

Turn to Set-Press to Save

Turn to Set-Press to Save      

      

CobraNet Transport Latency: Turn an Encoder knob to set the CobraNet 
transport latency: either 5.33, 2.66, or 1.33msec. Press the knob to confi rm 
your choice. This latency must match the Cobranet source for proper Cobranet 
reception.

Cobranet Transport Latency      

Cobranet Transport Latency      

   

   

Turn to Set-Press to Save

Turn to Set-Press to Save