Hunter Fan TYPE 2 Manuel D’Utilisation

REV: 5/94

FALLING.

SCREW COULD RESULT IN FAN

UNSCREWING.

IS IN THE UP POSITION.

NOTE:

ASSURES LOCKING TAB IN CANOPY

HOLES IN CEILING PLATE THAT

MUST BE IN UP POSITION. USE SET OF

ON THE SIDE. LOCKING TAB IN SIDE

CEILING, THERE ARE (2) SETS OF HOLES

FOR MOUNTING FAN ON VAULTED

A. INSERT PIPE NIPPLE THROUGH

CANOPY AND FEED WIRES FROM TOP
OF MOTOR THROUGH PIPE NIPPLE.
SCREW PIPE NIPPLE INTO FAN UNTIL
TIGHT (AT LEAST 4-1/2 TURNS).
THE SETSCREW LOCKING THE PIPE
NIPPLE TO MOTOR MUST BE
TIGHTENED VERY SECURELY (SEE
FIGURE 5B). FAILURE TO TIGHTEN

THE PIPE NIPPLE HAS A SPECIAL
COATING ON THE THREADS. DO NOT
REMOVE. THE COATING IS TO HELP
PREVENT THE NIPPLE FROM

DO NOT LIFT MOTOR BY WIRES.

B. BEING CAREFUL NOT TO SCRATCH

THE CANOPY FINISH, HANG THE
FAN FROM THE HOOK IN THE CEILING
PLATE USING ONE OF THE (3) SLOTS
IN THE CANOPY. SEE FIGURE 5A.

CAUTION:

FIGURE 5A.

THE (3) SLOTS IN THE CANOPY. SEE

HOOK IN THE CEILING PLATE USING ONE OF

CANOPY FINISH, HANG THE FAN FROM THE

C. BEING CAREFUL NOT TO SCRATCH THE

DO NOT LIFT MOTOR BY WIRES.

FAN.

MUST FIT SNUG AGAINST THE TOP OF THE

CANOPY ASSEMBLY SCREWS, THE CANOPY

TO ENSURE PROPER ENGAGEMENT OF THE

RESULT IN THE FAN FALLING.

ARE TIGHT. FAILURE TO DO SO COULD

ADAPTOR KIT. MAKE CERTAIN THE SCREWS

WITH LOCKWASHERS PACKAGED WITH THE

OF THE FAN USING (3) #10-32 SCREWS

B. NEXT, SECURE THE CANOPY TO THE TOP

CANOPY SLIGHTLY, ELIMINATING THE SPACE.

IF A SPACE IS PRESENT, ROTATE THE

OF THE CANOPY AND THE TOP OF THE FAN.

WITHOUT A SPACE BETWEEN THE BOTTOM

CANOPY SITS FLAT ON TOP OF THE FAN

PATTERN BY CHECKING TO SEE THAT THE

CERTAIN YOU HAVE LOCATED THE HOLE

THE PROPER HOLES. SEE FIGURE 5. MAKE

CANOPY ON TOP OF THE FAN AND ALIGN

CANOPY ASSEMBLY SCREWS. PLACE THE

THE (3) REMAINING HOLES ARE FOR THE

OVER THE ADAPTOR ON TOP OF THE FAN.

BOTTOM. THE LARGE CENTER HOLE FITS

A. THE CANOPY HAS (4) HOLES IN THE

HANGING FAN

LO PROFILE FAN

PAGE 2

FORM NO. 40987-01

NOTE:

STEP 5:

STEP 4:

FAN ASSEMBLY

STEPS 5 THROUGH 7 AND DECIDE WHICH STYLE OF MOUNTING TO USE.

AND ALSO AS A BALL TYPE HANGING FAN. THUS, INSTALLER'S CHOICE. CUSTOMER SHOULD READ

YOUR NEW HUNTER FAN CAN BE HUNG IN (2) DIFFERENT MANNERS, ONE BEING AS A LOW PROFILE FAN

NOTE: ASSEMBLY METHODS FOR INSTALLER'S CHOICE HANGING SYSTEM

SEE FIGURE 4B.

AND (2) FLATWASHERS FOR MOUNTING. DRILL (2) PILOT HOLES FOR THE MOUNTING SCREWS 9/64" DIAMETER.

PLATE TO THE 2 X 4 BRACE WHICH SUPPORTS THE OUTLET BOX. USE (2) #10 WOODSCREWS 3" LONG

B. THREAD THE LEAD WIRES THROUGH THE OPENING IN THE CEILING PLATE AND INSTALL THE CEILING

BUSHINGS. DO NOT OVER-TIGHTEN.

TIGHTEN THE CEILING PLATE MOUNTING SCREWS ONLY ENOUGH TO PROVIDE SLIGHT COMPRESSION OF THE

WHEN ATTACHING CEILING PLATE TO THE OUTLET BOX SUPPORT, MAKE CERTAIN BUSHINGS REMAIN IN PLACE.

OF THE BUSHING INTO THE THREE HOLES IN THE CEILING PLATE. SEE FIGURE 4A.

A. INSTALL THE (3) RUBBER BUSHINGS INTO THE TOP OF THE CEILING PLATE BY INSERTING SMALL SIDE

INSTALLATION OF THE CEILING PLATE

MOUNTING SCREWS

FLAT WASHERS

OUTLET BOX

CEILING PLATE

FIGURE 4A.

CEILING PLATE

BUSHING

2 X 4 WOOD BRACE

FIGURE 4B.

2 X 4 WOOD BRACE

CEILING JOIST

#8 WOOD SCREW

& WASHER (2) REQUIRED

OUTLET BOX

CEILING

FIGURE 2.

FIGURE 3.

CONNECTOR

6" MIN. LEAD LENGTH