Bunn 41343 Manuel D’Utilisation

Page 30

 

This function allows the operator to choose whether 

or not to display the advertising message that was en-

tered into the brewer with an AD CARD. This message 

will be displayed when the brewer is not in use.

Procedure to Enable/Disable Ads:

1.  Press and hold upper right hidden switch until the 

display reads UNITS. Release switch. Continue to 

press and release switch until the display reads 

ENABLE ADS. The YES or NO will be flashing to 

indicate the current selection.

2.  Press and release the NO to disable this function 

(no ads will be displayed on the screen), or;

3.  Press and release the YES to enable this function 

(ads will be displayed on screen).  

4.  When finished, press and release DONE to save 

the new setting, exit the ENABLE ADS function and 

advance to the next function screen, SET  TEMP.  

Another alternative is to press and release the 

ON/OFF switch (either on DUAL brewers) located 

on the front switch panel to exit the ENABLE ADS 

function and return to the MAIN SCREEN.

 

This function allows the operator to set the brew 

water temperature in the tank.  It also sets the hot 

water faucet dispense temperature.

1.  Press and hold upper right hidden switch until the 

display reads UNITS. Release switch.  Continue to 

press and release switch until the display reads  

SET TEMP.

2.  To adjust the brew temperature, press (-) to de-

crease or (+) to increase the brew temperature.

3.  When finished, press and release DONE to save 

the new setting, exit the SET TEMP function and 

advance to the next function screen,  SET READY. 

Another alternative is to press and release  the ON/

OFF switch (either on DUAL brewers) located on 

the front switch panel to exit the SET TEMP func-

tion and return to the MAIN SCREEN.

 

This function allows the operator to set the mini-

mum temperature allowable to start a brew cycle. The 

range can be from 185˚F (85˚C) to within 2˚F (-1.7°C) 

of the SET TEMP. The water must be at the SET READY 

temperature or higher for the display to indicate READY 

TO BREW. If brew lockout is enabled, the brewing pro-

cess will not start below this READY temperature.

NOTE: The upper limit for SET READY temperature 

is 2˚F (-1.7°C) less than the water temperature (SET 

TEMP) setting.

-1000

213.8

101.0

200

93.3

-500

212.9

100.5

200

93.3

0

212.0

100.0

200

93.3

500

211.1

99.5

200

93.3

1000

210.2

99.0

200

93.3

1500

209.3

98.5

200

93.3

2000

208.4

98.0

200

93.3

2500

207.4

97.4

200

93.3

3000

206.5

96.9

199

92.8

3500

205.6

96.4

198

92.2

4000

204.7

95.9

197

91.7

4500

203.8

95.4

196

91.1

5000

202.9

94.9

195

90.6

5500

201.9

94.4

195

90.6

6000

201.0

93.9

194

90.0

6500

200.1

93.4

193

89.4

7000

199.2

92.9

192

88.9

7500

198.3

92.4

191

88.3

8000

197.4

91.9

190

87.8

8500

196.5

91.4

189

87.2

9000

195.5

90.8

188

86.7

9500

194.6

90.3

187

86.1

10000

193.7

89.8

186

85.6

Brew water temperature is factory set at 200

∞ F (93.3∞ C)

Areas of high altitude will require lowering this tempera-

ture to prevent boiling.  This chart should be used as a

guide when readjusting the brew water temperature.

Altitude

(Feet)

Boiling point

of water

∞ F          ∞ C

Recommended

water temperature

∞ F          ∞ C

35665.0000A  05/04  © 2004  Bunn-O-Matic Corporation

ENABLE ADS ?

 NO DONE  YES

SET TEMP: XXX°

 (-)  DONE  (+)

SET READY: XXX°

 (-)  DONE  (+)

41343 080108