Proma 141030 PCB Bubble Etching Machine with Heater 141030 データシート
製品コード
141030
gie
- tec
Technische Änderungen vorbehalten
l
l
l
l
Gie-Tec GmbH An der Schlierbach 18 D-36132 Eiterfeld Tel.: +49 (0)6672/919-910 E-Mail:info@gie-tec.de
www
.gie-tec.de
ATTENTION
The etching device is designed for
using sodium persulfat.
Don`t fill in iron-III-chloride or other
chemicals!
using sodium persulfat.
Don`t fill in iron-III-chloride or other
chemicals!
ATTENTION
Carry corresponding protective
clothing (acid and alkal-proof
protection gloves, protective goggles,
overall or apron) when applying the
bath or when working with the device.
clothing (acid and alkal-proof
protection gloves, protective goggles,
overall or apron) when applying the
bath or when working with the device.
At skin contact, rinse immediately
with lukewarm water and soap.
with lukewarm water and soap.
Markierung
1. Switch-on the glass heater only when the tank is filled
and the pump is activated!
2. The water level should be a few millimeters
above the marking of the heating rod so the
heater regulation can work correctly.
heater regulation can work correctly.
3. Do not heat the bath to a temperature above 50°C
since this can cause a deformation of the acrylic
tank and a malfunctioning of the thermometer.
tank and a malfunctioning of the thermometer.
4. Connect the power cord of the glass heater to mains
voltage (AC 230V/50-60Hz). Turning the adjustment
knob in plus-direction increases the temperature, the
temperature is reduced by turning into the minus
knob in plus-direction increases the temperature, the
temperature is reduced by turning into the minus
direction
5. To adjust the temperature please turn the knob to
maximum (+).
Control temperature rise while heating up. When Temperature of 45°C is
reached, turn adjustment knob slowly in direction (-) until the indicator lamp
ist deactivated and the glass heater is OFF.
reached, turn adjustment knob slowly in direction (-) until the indicator lamp
ist deactivated and the glass heater is OFF.
1.5 Adjusting the heating regulator
1. Switch-on the membrane pump by connecting the feeder to mains voltage.
2. Plug in the power cord f the heater to mains voltage. When bath
2. Plug in the power cord f the heater to mains voltage. When bath
temperature of 45°C is reached you can start etching.
3. Clamp the board in the board holder and make sure, that the board is fixed
well.
4. Immerse the board holder with the board into the tank.
5. After 5 to 10 minutes, the copper is removed.
6 Rinse the printed circuit board in water and dry the board
5. After 5 to 10 minutes, the copper is removed.
6 Rinse the printed circuit board in water and dry the board
Please notice:
The bath is saturated if the color of the liquid changes to a deep blue and
the etching times extend to more than 30 minutes. It has to be renewed.
The etching liquid can remain in the cuvette without losing it´s effect for a
few days. Liquid losses due to evaporation can be compensated using
water.
water.
2. Etching procedure
ATTENTION!
Pay attention to the temperature of
etching bath. Temperaure higher than
+50°C may result in deformation of
the acrylic tank and may damage the
glass heater.
etching bath. Temperaure higher than
+50°C may result in deformation of
the acrylic tank and may damage the
glass heater.
If you don´t want to use the etching
device of a longer time, please
discharge the tank. Fill the etching
fluid in a plastic canister and store
them out of range of children and
foods.
After this fill water (approx.: 1l) in the
tank and switch on the membrane
pump for a few minutes to clean the
air curtain tube.
device of a longer time, please
discharge the tank. Fill the etching
fluid in a plastic canister and store
them out of range of children and
foods.
After this fill water (approx.: 1l) in the
tank and switch on the membrane
pump for a few minutes to clean the
air curtain tube.