Korg D3200 ユーザーズマニュアル

In the SYSTEM/MIDI, “Control” tab page, is the effect 
selected by “Control Change Assign” enabled?
→ Go to the EFFECT, “EFFRouting” tab page and verify 

that the effect is enabled.

Are you using the correct device to control the effect?
→ Control the effect using the device specified by the 

 setting in the SYSTEM/

, “Control” tab page. (

Is the selected effect set to effect program number “000” 
(=NO EFFECT) or to an effect program number that does 
not include a control function?
If you are controlling via MIDI, does the MIDI channel 
number of the D3200 match the MIDI channel of the 
transmitting MIDI device? (

→p.124)

Is the effect program’s Ctrl setting turned on? (

Is the external send level setting set to zero or nearly 
zero?
→ Go to the MIXER, SEND (EFF/AUX/REC), “AUX1 

 tab page, and raise the external 

send level.

Is the output of your external effect connected to the 
INPUT 1–INPUT 12 jacks, and input to the mixer 
channels?
→ Go to the MIXER, CH INPUT/SubMixer, “Ch Assign” 

tab page and make the appropriate assignments.

Have sub input settings been made correctly? (

Is the DRUMS key turned off?
Is the DRUMS fader lowered?
Is the rhythm assign setting appropriate?
→ If the rhythm is assigned to a CH Input, input the 

rhythm to a mixer channel.

Is the recorder stopped?
→ Press the PLAY key to play back. The rhythm will 

sound while the recorder is recording or playing,

If you want to preview the rhythm while the recorder is 
stopped, go to the SESSION DRUMS, “SessionDr.” tab 
page and turn the RUN button on.
You may have selected a silent drum pattern.
The session drum volume may be too low.
→ Use DRUMS fader to adjust the volume.

Is the DRUMS key off? (

Some keys do not function while the recorder is playing 
or recording.
→ Stop the recorder, and then perform the operation.
Some keys do not function while Scrub is on.
→ Turn off Scrub, and then perform the operation. 

(

Is a dialog box open?
→ Click either the Yes, No button to close the dialog box.

In the case of a 24-bit song, only sixteen channels are 
available, so this key will not function.

Are the MIDI cables connected correctly? (

A MIDI cable may be broken.

Does the synchronization signal being output by the 
D3200 match the synchronization signal your MIDI 
sequencer is receiving?
→ Go to the SYSTEM/MIDI, “MIDI/MMC” tab page 

and check the “MIDI Sync” setting. (

Are the synchronization settings of your MIDI sequencer 
appropriate?
→ Refer to the owner’s manual of your MIDI sequencer.

In the SYSTEM/MIDI, “MIDI/MMC” tab page, is 
“MMC Mode”

 set to “Receive”?

In the above page, is “MMC Device ID” set to match the 
MMC device ID setting of your MIDI sequencer? 
(

→p.125)

→ For some MIDI sequencers, the MMC device ID setting 

may differ.

Is your MIDI sequencer set to transmit MMC?
→ Refer to the owner’s manual of your MIDI sequencer.

Do the MIDI channels of the D3200 and your MIDI 
sequencer match?
→ Go to the SYSTEM/MIDI, “MIDI/MMC” tab page 

and check the “Global Ch” setting. (

Are program changes turned off?
→ Check the settings in the SYSTEM/MIDI, “MIDI/

 tab page. (

→p.124)

→ If the D3200 is set as an MTC slave, it may take several 

seconds for synchronization to occur.

→ Do the Frame Rate settings match? (→p.125)

→ If you are using MTC to synchronize, the MIDI se-

quencer to which you are synchronizing must support 
MTC.

In the SYSTEM/MIDI, “MIDI/MMC” tab page, is 
“MMC Mode”

 set to “Transmit”?

Is the MMC slave device set so that it will receive MMC?
Does the D3200’s MMC Device ID match the external 
MIDI device’s MMC Device ID?

Is the device that is receiving the control changes set to 
record all MIDI channels 1–16?
Are control changes turned off?
→ Check the settings in the SYSTEM/MIDI, “MIDI/

 tab page. (

→p.124)