Breckwell W3000 사용자 설명서

 

 
Note: The W3000FS wood stove is heavy. Be prepared to handle 
the weight to avoid damage or injury. Wearing gloves during 
installation is recommended. 
 
1. 

Carefully lay the stove on its back on carpet or other material 
that will prevent damage to the finish. 

 
2. 

Align the mounting tabs on the pedestal with the mounting 
holes in the bottom of the stove making sure that the opening 
in the pedestal is facing the back of the stove. Using the two 
3/8” x 3/8” bolts firmly tighten the pedestal to the stove. 

 
3. 

Carefully stand the stove back up. If the stove is not centered 
on the pedestal, loosen the bolts (do not fully remove), realign 
the stove, and firmly retighten the bolts. 

 

WARNING: Electrical Grounding Instructions. This appliance is 
equipped with a three-prong (grounding) plug for your 
protection against shock hazard and should be plugged 
directly into a properly grounded three-prong receptacle. Do 
not cut o remove the grounding prong from this plug. 
 
Both blower kits contain a blower assembly and speed control unit. 

 
Never operate the stove without either the blower or the blower 
cover in place. 
 
1. 

Using a 3/8” wrench or socket, remove the 5 screws holding 
the blower cover plate in place. Do not discard the cover plate/ 
(If the blower is ever removed, the cover plate MUST be 
reinstalled) place it in the pedestal, or any other safe place. 

 
2. 

Using the 5 screws from step 1, install the blower as shown in 
figure 4. Firmly tighten the screws, but so not over tighten as 
you may strip the holes out. 

 
3. 

Plug the speed control into the nearest outlet. Route the fan 
cord so that it is not coming into contact with any part if the 
stove. Plug the blower cord into the speed control unit. 

 

 

 
 
 
 

 

 

 
1. 

Carefully unpack the blower assembly. Determine which side of 
the stove the power supply will be located. The blower comes 
standard with the power cord installed on the right side of the 
blower housing. If power outlet is on the left side, the blower 
cord can be rerouted to the left side by removing the rubber 
grommet and cord, and reinstalling on the left side in the same 
location. 

 
2. 

Install blower assembly to the stove face by first loosening the 
two ¼” cap screws underneath the ash lip. Locate the blower 
assembly by lining up the screws on the blower housing to the 
two cap screws. Slide blower housing from left to right, and 
then tighten the two cap screws. 

 
3. 

Route the fan cord so that it is not coming into contact within 
part if the stove. Plug the blower cord into the power outlet. 

 

 
1. 

Making sure that all minimum clearances are met, position the 
stove on the floor protection. Draw an outline around the 
pedestal on the floor protector. Remove the stove. 

 
2. 

In the center of the outline of the pedestal foot print, cut a 4 ½” 
diameter hole through the floor protector and floor. Make four 1 
½” cuts in one end of the tube and fold out to make flaps. Insert 
the tube through the hole, cover it with the screen, and secure 
it to the floor protector. 

 
3. 

Place the stove back on the floor protector. If the stove is to be 
fastened to the floor, use lag bolts long enough to penetrate 
well into the floor. Use the mounting holes provided inside the 
pedestal. 

 
4. 

Install the pedestal cover by aligning the screw holes in the 
pedestal with the holes in the cover, making sure that the cover 
recesses into the pedestal (see figure 5). 

 
5. 

Using a silicone dealer, seal all cracks between the pedestal 
cover and the stove, as well as cracks between the floor 
protector and pedestal base. 

 

 
 

 

BLOWER ASSEMBLY 

W3000FS