Elica EFG630SM 설치 설명서
9
Installation
Installation - Ducting version
It is recommended that the vent system be installed be-
fore the hood is installed.
Before making cutouts, make sure there is proper clear-
ance within the ceiling or wall for exhaust vent.
Check your ceiling height and the hood maximum height
before you select your hood.
Disconnect power.
Determine which venting method to use: roof, wall, or
non-vented.
Select a flat surface for assembling the range hood.
Place covering over that surface.
Using 2 or more people, lift range hood onto covered
surface.
Range hood mounting screws installation
Determine and mark centerline on the wall the canopy
hood will be installed.
Tape template in place, aligning the template centerline
and bottom of template with hood bottom line and with
the centerline marked on the wall.
A. Centerline
B. Fastener locations
C. Mounting height reference
B. Fastener locations
C. Mounting height reference
Marck centers of the fastener locations through the tem-
plate to the wall.
IMPORTANT: All screws must be installed into wood. If there
is no wood to screw into, additional wall framing supports
may be required.
Remove the template.
Drill 3/16” (4.8 mm) pilot holes at all locations where
screws are being installed into wood.
Install the 2 - 5 X 45 mm mounting screws. Leave a 1/4”
(6.4 mm) gap between the wall and the back of the screw
head to slide range hood into place.
•
•
•
•
•
•
•
•
•
•
•
•
Secure the bracket to the wall:
Position vent cover bracket on wall about 1/8” (3.0mm)
away from the ceiling.
Mark the hole locations.
Drill 3/8” (9.5mm) holes for wall anchors and insert an-
chors flush with the wall.
away from the ceiling.
Mark the hole locations.
Drill 3/8” (9.5mm) holes for wall anchors and insert an-
chors flush with the wall.
A. 8 x 40 mm drywall anchors
B. Centerline on wall
C. Vent cover support bracket
D. 5 X 45 mm screws
Attach vent cover support bracket to wall.
Mounting the hood
Using 2 or more people, hang range hood on 2 mount-
ing screws though the mounting slots on back of hood.
A. Mounting screws
B. Mounting slots
C. Lower mounting screws
Remove the grease filter andmount the hood onto the upper
screws.
Level the range hood and tighten upper mounting screws.
Install 2 - 5 X 45 mm lower mounting screws and tighten.
•
•
•
•
•
•
•
•
•
A
B
C
D
Ver
tic
al C
en
te
rlin
e
CL
L
L
A
W
R
A
E
R
E
T
A
L
P
M
E
T
G
N
I
T
N
U
O
M
E
G
D
E
M
O
T
T
O
B
N
G
I
L
A
E
N
I
L
L
I
C
N
E
P
H
T
I
W
M
O
T
T
O
B
G
N
I
T
A
C
I
D
N
I
D
O
O
H
E
H
T
F
O
t
h
g
i
e
H
n
o
it
a
ll
a
t
s
n
I
T
R
O
P
P
U
S
L
L
A
W
R
A
E
R
R
O
S
D
U
T
S
H
G
U
O
R
H
T
S
E
L
O
H
T
O
L
I
P
"
6
1
/
3
)
O
W
T
(
2
L
L
I
R
D
e
n
i
L
l
a
t
n
o
z
ir
o
H
A
C
B
1/4”
(6.4 mm)
A
B
C