Справочник Пользователя для Sony HDCU3300
40
Locations and Functions of Parts
The HKCU1001 consists of an EN-A front board and a
VDA-A rear board.
When these boards are installed in the front and rear
expansion slots of the unit, the unit outputs SD composite
signals, waveform monitor output signals, and picture
monitor output signals through the VDA-A board.
VDA-A rear board.
When these boards are installed in the front and rear
expansion slots of the unit, the unit outputs SD composite
signals, waveform monitor output signals, and picture
monitor output signals through the VDA-A board.
For details on installation, contact a Sony service or sales
representative.
representative.
EN-A Board
a SD signal format indicators
Either of these indicators lights, corresponding to the SD
signal format.
Either of these indicators lights, corresponding to the SD
signal format.
b SC PHASE (subcarrier phase) switch
Used to adjust the SC phase with respect to the reference
signal (black burst).
Press and hold the switch towards ADV to advance the
phase or towards DELAY for delay. The phase is advanced
or delayed only while the switch is held pressed.
Used to adjust the SC phase with respect to the reference
signal (black burst).
Press and hold the switch towards ADV to advance the
phase or towards DELAY for delay. The phase is advanced
or delayed only while the switch is held pressed.
VDA-A Board
a VBS 1, 2 (composite video output 1, 2) connectors
(BNC-type)
The signal from the video camera may be output as two
analog composite signals.
analog composite signals.
b PIX OUT (picture monitor output) connector
(BNC-type)
Outputs the video signal for a picture monitor selected
with the PICTURE MONITOR button of an RCP-700/900
series Remote Control Panel or MSU-900 series Master
Setup Unit.
Character signals or marker signals can be superimposed
on the video signal output through this connector.
with the PICTURE MONITOR button of an RCP-700/900
series Remote Control Panel or MSU-900 series Master
Setup Unit.
Character signals or marker signals can be superimposed
on the video signal output through this connector.
For details on these operations, refer to the Master Setup
Unit or Remote Control Panel manuals.
Unit or Remote Control Panel manuals.
c WF OUT (waveform monitor output) connector
(BNC-type)
Outputs the video signal for a waveform monitor selected
with the WF MONITOR button of an RCP-700/900 series
Remote Control Panel or MSU-900 series Master Setup
Unit.
with the WF MONITOR button of an RCP-700/900 series
Remote Control Panel or MSU-900 series Master Setup
Unit.
For details on these operations, refer to the Master Setup
Unit or Remote Control Panel manuals.
Unit or Remote Control Panel manuals.
HKCU1003 Multi Interface Unit
(optional)
(optional)
To reduce the risk of electric shock, fire or injury, do not
open the cabinet. To adjust the internal settings, refer to
qualified service personnel.
open the cabinet. To adjust the internal settings, refer to
qualified service personnel.
The HKCU1003 consists of an EN-B front board and three
VDA rear boards (A/B/C). Only the VDA-A board can
actually be used with the HDCU3300 at present, and the
HKCU1003 has almost the same function as the
HKCU1001.
VDA rear boards (A/B/C). Only the VDA-A board can
actually be used with the HDCU3300 at present, and the
HKCU1003 has almost the same function as the
HKCU1001.
The VDA-B board can be used, but the FRAME REF IN
connector does not function.
connector does not function.
For details on installation, contact a Sony service or sales
representative.
representative.
EN-A
NTSC
PAL
SC PHASE
ADV
DELAY
1
SD signal format indicators
2
SC PHASE switch
VDA-A
1
2
PIX
OUT
OUT
WF
OUT
OUT
VBS
1
VBS 1, 2 connectors
2
PIX OUT connector
3
WF OUT connector
Note
Note