MTD H660G Benutzerhandbuch
13
Both Wheels Driving: Insert the click pin through
the hole in the hub of the rim and the inside hole on
the snow thrower’s right axle. This position is good
for heavy snow as there is power drive in both
wheels.
the hole in the hub of the rim and the inside hole on
the snow thrower’s right axle. This position is good
for heavy snow as there is power drive in both
wheels.
IMPORTANT:
Never operate the snow thrower with the
click pin inserted through both the rim and the outside
hole in the axle. Doing so can result in serious damage
to the drive system.
hole in the axle. Doing so can result in serious damage
to the drive system.
SECTION 6: MAINTAINING YOUR SNOW THROWER
WARNING:
Before servicing, repairing or
inspecting, disengage all clutch levers and
stop engine. Wait until all moving parts have
come to a complete stop. Disconnect spark
plug wire and ground it against the engine to
prevent unintended starting.
stop engine. Wait until all moving parts have
come to a complete stop. Disconnect spark
plug wire and ground it against the engine to
prevent unintended starting.
Lubrication
Engine
•
Refer to the engine manual for maintenance
procedures and instructions.
procedures and instructions.
WARNING:
When following instructions in
the engine manual for draining oil, be sure to
protect frame to avoid oil dripping onto
transmission parts.
protect frame to avoid oil dripping onto
transmission parts.
Gear Shaft
•
Lubricate the gear shaft with a good all-weather
multi-purpose light grease at least once a season or
after every 25 hours of operation.
multi-purpose light grease at least once a season or
after every 25 hours of operation.
IMPORTANT:
Keep all grease and oil off friction wheel
and drive plate.
Gear Case
•
The auger gearbox has been filled with grease at
the factory. If disassembled for repairs, lubricate
with 1-1/2 ounces of grease, part no. 737-0168.
the factory. If disassembled for repairs, lubricate
with 1-1/2 ounces of grease, part no. 737-0168.
IMPORTANT:
Do not overfill the gear case. Damage to
the seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.
grease in order to relieve pressure.
Wheels
•
Oil or spray lubricant into bearings at least once a
season. Pull the klick pins and remove wheels,
clean and coat axles with a multipurpose
automotive grease. See Figure 16.
season. Pull the klick pins and remove wheels,
clean and coat axles with a multipurpose
automotive grease. See Figure 16.
Figure 16
Auger Shaft
•
At least once a season, remove shear bolts on
auger shaft. Oil or spray lubricant inside shaft.
Also lubricate the auger bearings at least once a
season. See Figure 17.
auger shaft. Oil or spray lubricant inside shaft.
Also lubricate the auger bearings at least once a
season. See Figure 17.
Figure 17
Chute Directional Control
•
The worm gear on the chute directional control
should be greased with multipurpose automotive
grease.
should be greased with multipurpose automotive
grease.
Drive and Shifting Mechanism
•
Remove rear cover. Oil any chains, sprockets,
gears, bearings, shafts, and shifting mechanism at
least once a season. Use engine oil or a spray
lubricant. Avoid getting oil on rubber friction wheel
and aluminum drive plate. See Figure 18.
gears, bearings, shafts, and shifting mechanism at
least once a season. Use engine oil or a spray
lubricant. Avoid getting oil on rubber friction wheel
and aluminum drive plate. See Figure 18.
Figure 18
Klick Pin
Axle
Shear Bolts
Bearings
Bearings
Chain
Shift Lever
Gear Shaft
Avoid oil on
friction wheel and
drive plate
friction wheel and
drive plate