ATTO Technology 1550D Benutzerhandbuch
x
Route
Assigns an iSCSI protocol address to a target destination
device. If you try to map a new SCSI BTL to the same
iSCSI LUN, the new BTL overwrites the previous map.
Using the Delete identifier instead of SCSI removes the
map from its map table. In verbose mode, overwriting a
map requires secondary confirmation.
Assigns an iSCSI protocol address to a target destination
device. If you try to map a new SCSI BTL to the same
iSCSI LUN, the new BTL overwrites the previous map.
Using the Delete identifier instead of SCSI removes the
map from its map table. In verbose mode, overwriting a
map requires secondary confirmation.
Route [iSCSI] [default | Target Name] [lun] [SCSI <sb st
sl> | Bridge | Delete]
RouteDisplay
Displays s a combined list of iSCSI to SCSI bus, target,
LUN mappings. The optional target name limits the list to
maps which have that target name. The optional LUN
parameter limits the list further to the map which satisfies
a search for the given LUN.
Displays s a combined list of iSCSI to SCSI bus, target,
LUN mappings. The optional target name limits the list to
maps which have that target name. The optional LUN
parameter limits the list further to the map which satisfies
a search for the given LUN.
RouteDisplay iSCSI <default <lun> | Target Name <lun>>
SaveConfiguration
Issued with the restart option, cycles iPBridge power
after saving configuration changes. The norestart
option saves changes without restarting.
Issued with the restart option, cycles iPBridge power
after saving configuration changes. The norestart
option saves changes without restarting.
Note
Certain modifications require a system restart.
SaveConfiguration <Restart | NoRestart>
SCSIDomainValidation
Runs Domain Validation tests on the SCSI system which
may detect problems with SCSI cables, termination or
damaged transceivers. Tape drives attached to the
iPBridge should be loaded with media. The media is not
overwritten. Disable
Runs Domain Validation tests on the SCSI system which
may detect problems with SCSI cables, termination or
damaged transceivers. Tape drives attached to the
iPBridge should be loaded with media. The media is not
overwritten. Disable
before
running this test and reboot the iPBridge after running
the test.
the test.
SCSIDomainValidation
SCSIInitID
Specifies the persistent SCSI initiator ID used by the
iPBridge on this SCSI bus. All maps coinciding with the
user-specified ID are destroyed after this command is
issued.
Specifies the persistent SCSI initiator ID used by the
iPBridge on this SCSI bus. All maps coinciding with the
user-specified ID are destroyed after this command is
issued.
Default: 0x07
set SCSIInitID [sb] [0-15]
get SCSIInitID [sb]
set SCSIInitID [sb] [0-15]
get SCSIInitID [sb]
SCSIPortBusSpeed
Controls the transfer rate at which the iPBridge attempts
to negotiate with its SCSI devices
Controls the transfer rate at which the iPBridge attempts
to negotiate with its SCSI devices
Default: ultra320
set SCSIPortBusSpeed [sb] [fast | ultra | ultra2 | ultra160
set SCSIPortBusSpeed [sb] [fast | ultra | ultra2 | ultra160
| ultra320]
get SCSIPortBusSpeed [sb]
SCSIPortList
Lists the status of the SCSI port.
Lists the status of the SCSI port.
SCSIPortList
SCSIPortReset
Resets the SCSI bus.
Resets the SCSI bus.
SCSIPortReset [sb]
SCSIPortResetOnStartup
Controls whether the SCSI bus is reset each time the
iPBridge is powered up.
Controls whether the SCSI bus is reset each time the
iPBridge is powered up.
Default: enabled
set SCSIPortResetOnStartup [sb] [enabled | disabled]
get SCSIPortResetOnStartup [sb]
set SCSIPortResetOnStartup [sb] [enabled | disabled]
get SCSIPortResetOnStartup [sb]
SCSIPortSyncTransfer
Controls the iPBridge attempts to negotiate synchronous
SCSI transfers with devices on the specified bus.
Controls the iPBridge attempts to negotiate synchronous
SCSI transfers with devices on the specified bus.
Default: enabled
set SCSIPortSyncTransfer [sb] [enabled | disabled]
get SCSIPortSyncTransfer [sb]
set SCSIPortSyncTransfer [sb] [enabled | disabled]
get SCSIPortSyncTransfer [sb]
SCSIPortTermination
Configures the SCSI internal termination of the specified
SCSI port. Enabling termination allows the iPBridge to
act as a terminator at the end of a SCSI chain.
Configures the SCSI internal termination of the specified
SCSI port. Enabling termination allows the iPBridge to
act as a terminator at the end of a SCSI chain.
Default: enabled
set SCSIPortTermination [sb] [enabled | disabled]
get SCSIPortTermination [sb]
set SCSIPortTermination [sb] [enabled | disabled]
get SCSIPortTermination [sb]
SCSIPortWideTransfer
Controls the iPBridge attempts to negotiate wide SCSI
transfers with devices on the specified bus.
Controls the iPBridge attempts to negotiate wide SCSI
transfers with devices on the specified bus.
Default: enabled
set SCSIPortWideTransfer [sb] [enabled | disabled]
get SCSIPortWideTransfer [sb]
set SCSIPortWideTransfer [sb] [enabled | disabled]
get SCSIPortWideTransfer [sb]