ATTO Technology 1550D Benutzerhandbuch
xi
ATTO Technology Inc. iPBridge Installation and Operation Manual
SCSITargetLUNs
Controls the maximum number of SCSI LUNs per target
the iPBridge queries during a SCSI bus scan.
Controls the maximum number of SCSI LUNs per target
the iPBridge queries during a SCSI bus scan.
Default: 8
set SCSITargetLUNs [sb] [ 8 | 64]
get SCSITargetLUNs [sb]
set SCSITargetLUNs [sb] [ 8 | 64]
get SCSITargetLUNs [sb]
SCSITargets
Lists the physical devices that are connected and running
on the specified SCSI port.
Lists the physical devices that are connected and running
on the specified SCSI port.
SCSITargets [sb]
SerialNumber
Displays the serial number of the iPBridge. The serial
number is a 13 character field. The first seven
alphanumeric characters are an abbreviation
representing the product name. The remaining six digits
are the individual iPBridge number.
Displays the serial number of the iPBridge. The serial
number is a 13 character field. The first seven
alphanumeric characters are an abbreviation
representing the product name. The remaining six digits
are the individual iPBridge number.
get SerialNumber
SerialPortBaudRate
Configures the baud rate for the iPBridge RS-232 serial
port. The number of data bits per character is fixed at 8
with no parity.
Configures the baud rate for the iPBridge RS-232 serial
port. The number of data bits per character is fixed at 8
with no parity.
Default: 115200
set SerialPortBaudRate [2400 | 9600 | 19200 | 38400 |
set SerialPortBaudRate [2400 | 9600 | 19200 | 38400 |
57600 | 115200]
SaveConfiguration Restart command required
get SerialPortBaudRate
get SerialPortBaudRate
SerialPortEcho
Controls if the iPBridge echoes characters on its RS-232
port. When enabled, all non-control character keyboard
input is output to the display.
Controls if the iPBridge echoes characters on its RS-232
port. When enabled, all non-control character keyboard
input is output to the display.
Default: enabled
set SerialPortEcho [enabled | disabled]
get SerialPortEcho
set SerialPortEcho [enabled | disabled]
get SerialPortEcho
SNMP
Controls whether or not SNMP functions on the iPBridge.
Controls whether or not SNMP functions on the iPBridge.
Default: enabled
set SNMP [enabled | disabled]
get SNMP
set SNMP [enabled | disabled]
get SNMP
SNMPDumpMIB
Displays the contents of the ATTO iPBridge private
SNMP MIB to the current CLI session. For further
assistance with SNMP, consult your network
administrator.
Displays the contents of the ATTO iPBridge private
SNMP MIB to the current CLI session. For further
assistance with SNMP, consult your network
administrator.
SNMPDumpMIB
SNMPExtendedTraps
Regulates Extended (i.e., Device Transition and Device
Error) SNMP trap functionality.
Regulates Extended (i.e., Device Transition and Device
Error) SNMP trap functionality.
Default: disabled
set SNMPExtendedTraps [enabled | disabled]
get SNMPExtendedTraps
set SNMPExtendedTraps [enabled | disabled]
get SNMPExtendedTraps
SNMPTrapAddress
Regulates or displays IP Trap Addresses and Trap
Levels. Index is a value from 1 to 6. The IP address must
be in the same subnet as the iPBridge, and is the host that
wishes to receive traps. The supported severity levels
required to trigger a trap are: None, All, Warning,
Critical
Regulates or displays IP Trap Addresses and Trap
Levels. Index is a value from 1 to 6. The IP address must
be in the same subnet as the iPBridge, and is the host that
wishes to receive traps. The supported severity levels
required to trigger a trap are: None, All, Warning,
Critical
Default IP address: 0.0.0.0
Default level: none
set SNMPTrapAddress [index] [xxx.xxx.xxx.xxx] [None |
Default level: none
set SNMPTrapAddress [index] [xxx.xxx.xxx.xxx] [None |
All | Warning |Critical]
get SNMPTrapAddress [index]
is enabled on a data
port, a VLAN ID for that port must be specified. All SNMP
traps are sent with the same VLAN tag.
traps are sent with the same VLAN tag.
Default: disabled
set SNMPTraps [enabled |disabled] <[dp1] [VLAN ID]>
get SNMPTraps <[dp1] [VLAN ID]>
set SNMPTraps [enabled |disabled] <[dp1] [VLAN ID]>
get SNMPTraps <[dp1] [VLAN ID]>
SNTP
Controls whether SNTP time server is used.If
Controls whether SNTP time server is used.If
enabled on a data port, a VLAN ID for that port must be
specified.
specified.
Default: enabled
set SNTP [enabled | disabled] <[dp1] [VLAN ID]>
SaveConfiguration Restart command required
get SNTP <[dp1] [VLAN ID]>
set SNTP [enabled | disabled] <[dp1] [VLAN ID]>
SaveConfiguration Restart command required
get SNTP <[dp1] [VLAN ID]>