ATTO Technology 1550D Benutzerhandbuch
ix
ATTO Technology Inc. iPBridge Installation and Operation Manual
iSCSIWANIPAddress
Sets or displays the IP address reported to an iSCSI
initiator located outside the iPBridge LAN. If this
iPBridge is behind a NAT router, the address must be set
to the external IP address of the router. Setting the
address to 0.0.0.0 causes the iPBridge to be inaccessible
from outside the LAN.
Sets or displays the IP address reported to an iSCSI
initiator located outside the iPBridge LAN. If this
iPBridge is behind a NAT router, the address must be set
to the external IP address of the router. Setting the
address to 0.0.0.0 causes the iPBridge to be inaccessible
from outside the LAN.
Default: 0.0.0.0
set iSCSIWANIPAddress [dp1] | all] [xxx.xxx.xxx.xxx]
get iSCSIWANIPAddress [dp1] | all]
set iSCSIWANIPAddress [dp1] | all] [xxx.xxx.xxx.xxx]
get iSCSIWANIPAddress [dp1] | all]
iSNSLoginControl
Specifies whether the iPBridge delegates its access
control/authorization policy to an iSNS server.
Specifies whether the iPBridge delegates its access
control/authorization policy to an iSNS server.
Note
iSNSLoginControl cannot be used with
Default: disabled
set iSNSLoginControl [enabled | disabled]
get iSNSLoginControl
set iSNSLoginControl [enabled | disabled]
get iSNSLoginControl
iSNSServer
Specifies the IP address of a valid iSNS server from which
the iPBridge tries iSCSI initiator discovery. Set to
0.0.0.0 to disable iSNS server lookup.If
Specifies the IP address of a valid iSNS server from which
the iPBridge tries iSCSI initiator discovery. Set to
0.0.0.0 to disable iSNS server lookup.If
is
enabled, a VLAN ID must be specified for each data port.
All iSNS connections have the same VLAN tag.
All iSNS connections have the same VLAN tag.
Default: 0.0.0.0
set iSNSServer [xxx.xxx.xxx.xxx] <dp1] [VLAN ID]>
get iSNSServer
set iSNSServer [xxx.xxx.xxx.xxx] <dp1] [VLAN ID]>
get iSNSServer
IsReserved
Displays the reservation status of the current iPBridge.
Displays the reservation status of the current iPBridge.
IsReserved
Password
Specifies the password used for all sessions: NDMP,
Telnet, FTP and ExpressNAV. Password is case sensitive,
0 to 32 characters, and cannot contain spaces. An empty
password can be configured by pressing the enter key
when prompted for the new password and new password
confirmation.
Specifies the password used for all sessions: NDMP,
Telnet, FTP and ExpressNAV. Password is case sensitive,
0 to 32 characters, and cannot contain spaces. An empty
password can be configured by pressing the enter key
when prompted for the new password and new password
confirmation.
Default: Password
set Password
set Password
Ping
Sends an ICMP echo request to the specified host.If
Sends an ICMP echo request to the specified host.If
is enabled, the VLAN ID must be provided.
ping [dp1] [xxx.xxx.xxx.xxx] <count <size>>
ReadOnlyPassword
Specifies a password which allows only read and no
writes. It is case sensitive, 0 to 32 characters, and cannot
contain spaces. An empty password can be configured by
not specifying one.
Specifies a password which allows only read and no
writes. It is case sensitive, 0 to 32 characters, and cannot
contain spaces. An empty password can be configured by
not specifying one.
Default: Password
set ReadOnlyPassword
set ReadOnlyPassword
ReadOnlyUsername
Specifies the user name which allows only read and no
writes. It is case insensitive, 1 to 32 characters, and
cannot contain spaces.
Specifies the user name which allows only read and no
writes. It is case insensitive, 1 to 32 characters, and
cannot contain spaces.
Default: user
set ReadOnlyUsername [username]
get ReadOnlyUsername
set ReadOnlyUsername [username]
get ReadOnlyUsername
Reserve
Reports the state of CLI reservation for the current CLI
session. If the command reports that Reservations are
enabled, then another CLI session has control of
parameter modification on the unit.
Reports the state of CLI reservation for the current CLI
session. If the command reports that Reservations are
enabled, then another CLI session has control of
parameter modification on the unit.
Reserve
RestoreConfiguration
Issued with the default option, forces the iPBridge
NVRAM settings to their original defaults. The saved
option undoes any changes made to this session since the
last save.
Issued with the default option, forces the iPBridge
NVRAM settings to their original defaults. The saved
option undoes any changes made to this session since the
last save.
RestoreConfiguration [Default | Saved]
RMON
Displays Ethernet data and allows data collection at
specified intervals. Get displays hex.
Displays Ethernet data and allows data collection at
specified intervals. Get displays hex.
Valid range for bucketsRequest= 1-180
Valid range for ethernetStat index = 1-3
Valid range for historyControl = 1-6
Valid range for ethernetHistory index = 1-6
Valid range for sampleIdx = 1-2147483647
Valid range for interval = 1-3600
Valid range for ethernetStat index = 1-3
Valid range for historyControl = 1-6
Valid range for ethernetHistory index = 1-6
Valid range for sampleIdx = 1-2147483647
Valid range for interval = 1-3600
Default: See
set rmon [idx] [bucketsRequest] [interval] [valid | invalid]
get rmon [ethernetStat | historyControl] <idx>
get rmon [ethernetHistory] <idx sampleIdx>
get rmon [ethernetStat | historyControl] <idx>
get rmon [ethernetHistory] <idx sampleIdx>