Heartland hcdwis Betriebsanweisung
30
7. Reinstall terminal box cover with wires inside terminal box. The
cover must be outside the box on the left side.
cover must be outside the box on the left side.
8. Make sure no wires are pinched by cover.
Option 2: Power supply cord method
1. Plug into a grounded 3 prong outlet.
2. Check that power supply cord does not touch dishwasher motor
or lower part of dishwasher tub.
2. Check that power supply cord does not touch dishwasher motor
or lower part of dishwasher tub.
Connect to water supply
Helpful Tip:
Compression fittings:
a. Slide nut onto copper tubing about 1” (2.5 cm).
b. Slide ferrule onto the tubing. Do not position ferrule on the end
of the tubing.
c. Put the tubing into the elbow as far as it will go.
d. Slide the nut and ferrule forward and start the nut onto the
elbow threads. Be gentle when handling and positioning the copper
tubing, it bends and kinks easily.
Compression fittings:
a. Slide nut onto copper tubing about 1” (2.5 cm).
b. Slide ferrule onto the tubing. Do not position ferrule on the end
of the tubing.
c. Put the tubing into the elbow as far as it will go.
d. Slide the nut and ferrule forward and start the nut onto the
elbow threads. Be gentle when handling and positioning the copper
tubing, it bends and kinks easily.
1. To prevent vibration during operation, route the water supply
line so that it does not touch the dishwasher base, frame or motor.
2. With copper tubing pushed into compression fitting as far as it
will go, use a wrench and tighten compression fitting nut to elbow
on water inlet valve.
line so that it does not touch the dishwasher base, frame or motor.
2. With copper tubing pushed into compression fitting as far as it
will go, use a wrench and tighten compression fitting nut to elbow
on water inlet valve.
3. Place paper towel under elbow. Turn on water supply and check
for leaks.
for leaks.
Connect to drain
1. To help minimize vibration, route drain hose to avoid contact
with motor, door springs, water line, cabinet, flooring or the edge of
the hole where it passes through the cabinet.
2. Do not remove drain loop from side of dishwasher.
with motor, door springs, water line, cabinet, flooring or the edge of
the hole where it passes through the cabinet.
2. Do not remove drain loop from side of dishwasher.
3. Place pan under end of drain hose. Pan will collect any water in
drain hose.
4. Place the smaller drain hose clamp onto the small end of the
drain hose.
drain hose.
4. Place the smaller drain hose clamp onto the small end of the
drain hose.
5. Push the drain hose into the connector up to the stop on the
drain hose.
drain hose.
6. Use pliers to open clamp and slide clamp onto connector between
stops on connector as shown.
stops on connector as shown.
screws
ADVERTENCIA
AVERTISSEMENT
3
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death,fire, or electrical shock.
nut
ferrule
elbow
drain
loop
hose clamp
stop
connector
hose clamp
stops