Lennox serefina ci2500dvf Benutzerhandbuch

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

4

All Millivolt appliances are equipped with a 
variable gas control valve. Flame height for 
these models may be adjusted through a range 
between fi xed low and high settings by rotating 
the HI/LO knob on the valve (see Figure 3), 
alternately, while the appliance is in opera-
tion. Adjust the fl ame height as desired after 
lighting the appliance by rotating the variable 
adjustment control (HI/LO) knob located on the 
front of the valve.

During the fi rst few burns of this appliance there 
will be some odor due to the “burn-in” of paints 
and lubricants (curing of the high temperature 
paint and burning off of lubricants used in the 
manufacturing process). 

Depending on your use, the burn-in period may 
take a few hours or a few days.  The dwelling 
should be well ventilated during these initial 
burns.

The appliance and venting system should be 
thoroughly inspected before initial use and at 
least annually by a qualifi ed service technician. 
However, more frequent periodic inspections 
and cleanings should be performed by the 
homeowner. Homeowner must contact a quali-
fi ed service technician at once if any abnormal 
condition is observed.

Refer to the maintenance schedule on page 5 
for maintenance tasks, procedures, periodic-
ity and by whom they should be performed.  
Always verify proper operation of the appliance 
after servicing.

Always turn off gas to the pilot (millivolt appli-
ances) before cleaning. Before re-lighting, 
refer to the lighting instructions in this manual. 
Instructions are also found on a pull-out panel 
located on the rear stove shield.

Keep lower control compartment clean by 
vacuuming or brushing at least twice a year. 
More frequent cleaning may be required due to 
excessive lint from carpeting, bedding materials, 
etc. It is important that control compartments, 
burners and circulating air passageways of the 
appliance be kept clean.

The viewing glass should be cleaned periodi-
cally to remove any build-up caused from the 
following:

•  During start-up, it is normal for condensa-
tion to form on the inside of the glass (this 
condensation and fog will usually disappear 
in a few minutes).  This can cause lint, dust 
and other airborne particles to cling to the 
glass surface. 

Crazing of Porcelain Enamel:  Porcelain 
enamel, when heated to high temperatures, 
is subject to crazing (a very fi ne and random 
network of hairline cracks on the surface of 
the porcelain).  Crazing is a normal occurrence 
when enamel is exposed to high temperatures.  
Your enamel fi nish will not be harmed nor will 
the function of the stove be impaired.

Repairing Chips: If the enamel fi nish on your 
stove becomes chipped, it can be touched up 
using enamel touch-up paint. For ordering 
information, see pages 16.

Cleaning Enamel Surfaces: To remove build-up 
of dust, dirt or crud from the enamel surfaces, 
combine baking soda and a little water to make a 
cleaning paste. Use a soft rag to rub the surface 
with the mix until the stains are removed.

To light millivolt appliances refer to the detailed 
lighting instructions found on page 13 (English) 
and page 14 (French). Millivolt appliance lighting 
instructions may also be found on the pull-out 
lighting instruction labels attached to the rear 
stove shield.  Refer to Figure 3 on page 3 for 
the location of the piezo igniter.

Millivolt appliances are fi tted with a burner ON/OFF 
Rocker Switch, located at the right  the rear stove 
shield as shown in Figure 1. Once the pilot is lit, 
the ON/OFF rocker switch will control the appliance 
ON/OFF operation. To operate:  Toggle the switch 
between its ON and OFF positions.

• Initial curing of the high temperature paint 
and burning off of lubricants used in the 
manufacturing process may result in a fi lm 
on the glass.  

• A white coating may form on the glass 
as a result of impurities and minerals in 
the fuel.

It is recommended that the glass be cleaned 
two or three times during each heating season, 
depending on the circumstances present.

Exterior glass may be cleaned with an non-
ammonia based household cleaner and warm 
water as desired (a gas stove glass cleaner is 
recommended). 

(Model Serefi na, Black Paint) Do not attempt to 
repaint the stove until the paint is completely 
cured. If the surface later becomes stained or 
marred, it may be lightly sanded and touched 
up with spray paint (See Small Area Paint 
Touch-Up, page 9). Paint is available at your 
local authorized Lennox Hearth Products dealer. 
Never attempt to paint a hot stove.

If the optional Blower Kit (see page 11 for 
ordering information) is installed, do not turn 
on a blower during the Burn-In period.  Do not 
place anything on the stove surface until the 
paint is completely cured.