Lennox elite vint-dvs-u Benutzerhandbuch
21
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
WARNINGS
•
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. For assistance or additional
information, consult a qualified installer, service
agency or your gas supplier.
•
Operation of this appliance when not connected
to a properly installed and maintained venting
system can result in carbon monoxide (CO)
poisoning and possible death.
•
Carbon monoxide poisoning – early signs of
carbon monoxide poisoning resemble the flu
with headaches, dizziness, or nausea. If you
have these signs, get fresh air at once! Have
the heater inspected by a qualified service
technician. Some people are more affected by
carbon monoxide than others. These include
pregnant women, people with heart or lung
disease or anemia, those under the influence
of alcohol and those at high altitudes.
12. Adjust the flame height (and heat output) by turning the flame
height knob clockwise for full flame and counter
clockwise for reduced flame.
13. Turn on the electric power to the appliance and set the blower
to the desired air flow after it turns on when the appliance
reaches operating temperature.
TO TURN OFF GAS TO APPLIANCE
1. Turn off the “ON/OFF” rocker switch and/or thermostat (if
installed) to its lowest setting.
2. Turn off electric power to the appliance if service is to be
performed.
3. Push in gas control knob slightly and turn clockwise
to “OFF.” Do not force.
SHUTDOWN PROCEDURE
To turn off the burner, turn the rocker switch to “OFF” or adjust
the thermostat (if installed) to a setting below room temperature.
The pilot will remain lit for future burner ignition. For complete
shutdown, see “TO TURN OFF GAS TO APPLIANCE” above.
Flame Color and Behavior
This appliance is designed for maximum heating efficiency. Therefore,
upon lighting of the main burner the flames will be semitransparent or
“bluish.” After 1020 minutes of operation the logs will heat up and the
flames will become a yellow/orange color.
Adjusting the appliance to cause the flames to turn orange sooner may
result in poor combustion, sooting and a hazardous situation. See Figure
31 showing proper flame appearance.
upon lighting of the main burner the flames will be semitransparent or
“bluish.” After 1020 minutes of operation the logs will heat up and the
flames will become a yellow/orange color.
Adjusting the appliance to cause the flames to turn orange sooner may
result in poor combustion, sooting and a hazardous situation. See Figure
31 showing proper flame appearance.
When testing for proper operation If an optional thermostat is installed
adjust it to its highest temperature setting. Visually determine that main
burner gas is burning properly: i.e., no floating, lifting or flashback.
Adjust the primary air shutter(s) as required. Check for proper main
burner operation at both high and low flame.
adjust it to its highest temperature setting. Visually determine that main
burner gas is burning properly: i.e., no floating, lifting or flashback.
Adjust the primary air shutter(s) as required. Check for proper main
burner operation at both high and low flame.
SIT Millivolt Gas Valve
Gas Control Knob
(Pilot / On / Off)
Flame Height Control
Knob (HI/LO)
No Blue Flame
Center
Soot at
Flame Tip
Dark Orange
Flame
IMPROPERLY
BURNING FLAME
Soot above
Flame Tip
No Soot at
Flame Tip
PROPERLY
BURNING FLAME
Semi-Transparent
Yellow Flame
Blue Flame
Center
Ports on Pan
Burner Assembly
Burner Flame Appearance
Figure 29
Figure 31
Figure 32
Figure 30
PILOT
ON
OF
F
HI
LO
Gas Control Knob
(pilot/on/off)
Bouton de contrôle
(veilleuse/ouverte/fermée)
Igniter / Allumeur
Flame Height Control Knob
- LO / HI +
(Commande De
Taille De Flamme)
Proper Pilot Flame Appearance