Futaba Corporation CGY760R-24G Benutzerhandbuch
21
20
*Please ix the cord connected to the main body with a margin.
Please install the CGY760R as it is in the center (vertical direction and horizontal
direction) of the tape without cutting the attached mount pad. This tape is designed to
effectively absorb the vibration from the model.
*Clean the oil on the bottom of the CGY760R and the machine mounting part with a
vacuum cleaner or the like.
*The CGY760R is designed to be screwed to the gyro mount. Please refer to the end
Please install the CGY760R as it is in the center (vertical direction and horizontal
direction) of the tape without cutting the attached mount pad. This tape is designed to
effectively absorb the vibration from the model.
*Clean the oil on the bottom of the CGY760R and the machine mounting part with a
vacuum cleaner or the like.
*The CGY760R is designed to be screwed to the gyro mount. Please refer to the end
of this manual for ixing method of screws and notes on installation.
The CGY760R Cant Be Mounted TROUBLESHOOTING
If any issues are noted during light (such as drifting, inconsistent hold or inconsistent
control rates) then please review the following troubleshooting recommendations.
control rates) then please review the following troubleshooting recommendations.
1. Always verify that the tail rotor and swash plate mechanisms operate, and that the
drive system is in proper working order.
2. Electromagnetic interference could be causing the problem. If you feel everything is
set up correctly and that the model is vibration free, then consider moving the gyro
sensor to a new location away from servos, ESC and drive motors.
sensor to a new location away from servos, ESC and drive motors.
3. Vibrations will decrease the performance of all gyro systems. Even though the
CGY760R gyro sensor is the most vibration resistant gyro sensor available, eliminating
vibrations will always improve performance. The CGY760R gyro sensor performs best
when the sensor is mounted rigidly to the airframe. This is mainly due to the sensing
of all 3 axes. It is highly recommended to avoid using soft foam pads as this may allow
the gyro to bounce around on the roll and pitch axis, causing instabilities and possible
loss of control during light.so that the roll and pitch sensing axis are in alignment with
the model. Any misalignments over 1/2 of a degree will cause a loss in performance.
Please take extra care in this step to ensure the optimum light performance.
vibrations will always improve performance. The CGY760R gyro sensor performs best
when the sensor is mounted rigidly to the airframe. This is mainly due to the sensing
of all 3 axes. It is highly recommended to avoid using soft foam pads as this may allow
the gyro to bounce around on the roll and pitch axis, causing instabilities and possible
loss of control during light.so that the roll and pitch sensing axis are in alignment with
the model. Any misalignments over 1/2 of a degree will cause a loss in performance.
Please take extra care in this step to ensure the optimum light performance.
Using The CGY760R With A Electric Model
DANGER
It is necessary to remove the pinion gear from the electric motor or
disconnect the motor from the ESC before powering the model up for
setup or bench testing. Electric motors are extremely powerful and
capable of delivering the power instantly, causing injury to yourself,
others, or the surroundings.
setup or bench testing. Electric motors are extremely powerful and
capable of delivering the power instantly, causing injury to yourself,
others, or the surroundings.
WARNING
Do not perform the linking procedure while the motor’s main wire
connected or the engine is operating as it may result in serious injury.
When the linking is complete, please cycle the receiver power and
ensure the receiver is properly linked to the transmitter.
Please power up your system in this order. Transmitter irst, fol-
lowed by the receiver.
If the CGY760R was previously linked to another transmitter, make
sure that transmitter is not operating while linking the receiver to the
new transmitter.
new transmitter.
Once the ESC is connected to the CGY760R, you need to complete all necessary
transmitter settings (ATV / EPA / REV / ETC) according to ESC instructions. Please
refer to page 109 of this manual for further suggestions on the use of the governor of
CGY760R and the electric model.
transmitter settings (ATV / EPA / REV / ETC) according to ESC instructions. Please
refer to page 109 of this manual for further suggestions on the use of the governor of
CGY760R and the electric model.
Link Method With Transmitter (FASSTest / T-FHSS)
1. Connect the CGY760R and GPB-1 and set the same mode as the transmitter linking
the CGY760R communication mode on the “Receiver” screen. (See page 40)
2. Keep the transmitter and receiver close to each other and turn on the receiver with the
transmitter in the link mode.
3. Wait for link waiting about 2 seconds after turning on receiver power.
4. If the RX LED changes from red lashing to green lighting, the link is complete. (The
4. If the RX LED changes from red lashing to green lighting, the link is complete. (The
link wait state ends in about 1 second.)
* Refer to the transmitters operation manual for complete details on how to place the
transmitter into the linking mode.
* When many FASSTest systems are turned on near the FASSTest system or when
many T-FHSS systems are turned on near the T-FHSS system, the CGY760R es-
tablishes a link to the transmitter It may be dificult. This is rare. However, if another
FASstest transmitter / receiver is linked at the same time, the CGY760R may link to
the wrong transmitter. If you do not notice such a situation, this is very dangerous.
To avoid this problem, we strongly recommend that you reconirm if the CGY760R is
actually controlled by the transmitter.
tablishes a link to the transmitter It may be dificult. This is rare. However, if another
FASstest transmitter / receiver is linked at the same time, the CGY760R may link to
the wrong transmitter. If you do not notice such a situation, this is very dangerous.
To avoid this problem, we strongly recommend that you reconirm if the CGY760R is
actually controlled by the transmitter.
* If the System Type of the transmitter is changed, the receiver will need to be re-linked
to the transmitter.