Futaba Corporation CGY760R-24G Benutzerhandbuch
19
18
AIL ---------- N
ELE --------- R
RUD -------- N
AIL ---------- N
ELE --------- N
RUD -------- N
ELE --------- N
RUD -------- N
AIL ---------- N
ELE --------- N
RUD -------- R
ELE --------- N
RUD -------- R
AIL ---------- N
ELE --------- R
RUD -------- R
RUD -------- R
AIL ---------- R
ELE --------- N
RUD -------- N
RUD -------- N
AIL ---------- R
ELE --------- R
ELE --------- R
RUD -------- N
AIL ---------- R
ELE --------- N
RUD -------- R
AIL ---------- R
ELE --------- R
ELE --------- R
RUD -------- N
AIL ---------- R
ELE --------- N
RUD -------- N
RUD -------- N
AIL ---------- R
ELE --------- N
RUD -------- R
AIL ---------- N
ELE --------- N
RUD -------- N
ELE --------- N
RUD -------- N
AIL ---------- N
ELE --------- R
RUD -------- R
RUD -------- R
Mounting The CGY760R
The CGY760R can be mounted in the orientation shown below unless it is installed
so that the roll and pitch detection axis are aligned with the model. However, if there
is a deviation of 1/2 or more of the degree, performance will degrade. In this step,
so that the roll and pitch detection axis are aligned with the model. However, if there
is a deviation of 1/2 or more of the degree, performance will degrade. In this step,
please pay special attention to ensure optimum l ight performance. Refer to the instal-
lation example below and select the gyro mounting direction with "Gyro Set Dir" (page
45) of the SWH basic menu.
lation example below and select the gyro mounting direction with "Gyro Set Dir" (page
45) of the SWH basic menu.
*The surface with the "CGY" mark in the i gure is the top (LED) side of the CGY760R.
Gyro Set Dir---1
Gyro Set Dir---4
Gyro Set Dir---5
Gyro Set Dir---6
Gyro Set Dir---2
Gyro Set Dir---3
AIL ---------- R
ELE --------- R
RUD -------- R
ELE --------- R
RUD -------- R
AIL ---------- R
ELE --------- R
RUD -------- R
ELE --------- R
RUD -------- R
AIL ---------- N
ELE --------- N
RUD -------- N
ELE --------- N
RUD -------- N
AIL ---------- N
ELE --------- N
ELE --------- N
RUD -------- R
AIL ---------- R
ELE --------- N
RUD -------- N
RUD -------- N
AIL ---------- N
ELE --------- R
RUD -------- N
AIL ---------- R
ELE --------- N
RUD -------- R
AIL ---------- R
ELE --------- N
RUD -------- R
AIL ---------- N
ELE --------- R
RUD -------- R
RUD -------- R
AIL ---------- N
ELE --------- R
RUD -------- R
RUD -------- R
*Depending on the type of mounting plate,
it is also possible to mount as shown in
the i gure.
it is also possible to mount as shown in
the i gure.
*Depending on the type of mounting plate,
it is also possible to mount as shown in
the i gure.
it is also possible to mount as shown in
the i gure.
It is necessary to set the motion direction of each gyro by "AGy.Dir", "EGy.
Dir" of "SWH. BASIC" menu (page 49) and "Gyro.Dir" of "RUD BASIC" menu
(page 63).
Dir" of "SWH. BASIC" menu (page 49) and "Gyro.Dir" of "RUD BASIC" menu
(page 63).
AIL-Aileron (Roll) axis / ELE-Elevator (Pitch) axis / RUD-Rudder (Yaw) axis
N --- Normal / R --- Revers
AIL ---------- R
ELE --------- N
RUD -------- N
RUD -------- N
AIL ---------- N
ELE --------- N
RUD -------- N
ELE --------- N
RUD -------- N