Vital Home Systems LLC 1050 Benutzerhandbuch
P a g e
| 4
© 2015 Vital Home Systems
How to Use
Programming Mode
The 1050 may also be programmed for certain
functions locally on the control panel face. See the
next section how to program the 1050 locally.
functions locally on the control panel face. See the
next section how to program the 1050 locally.
NOTE! You may only connect sensors and VC100
Valve controllers to the 1050 with the Vital Home
Systems Windows PC Software.
Valve controllers to the 1050 with the Vital Home
Systems Windows PC Software.
To Enter Programming
Mode
Step 1. With the VHS-1050 in Normal Mode, press
“Set” key
Step 2: Press “#” Key
Step 3: Enter Pin Code
Step 3: Enter Pin Code
The Pin code consists of a 4-digit number.
Factory default is “0000”.
Factory default is “0000”.
Step 4: Press “Set” key. A long beep is emitted and
Power LED lights ON Red.
NOTE:
Under Program Mode, a key-press interval
of five (5) seconds is allowed; the process
will abort automatically if the time is
exceeded, or incorrect entry is made. A
quick four (4)-beep sound will be emitted,
indicating Program exit Mode and return to
Normal Mode.
will abort automatically if the time is
exceeded, or incorrect entry is made. A
quick four (4)-beep sound will be emitted,
indicating Program exit Mode and return to
Normal Mode.
Once in Program Mode, if a key is not
pressed for 30 minutes. The Dialer will
sound five (5) quick-beeps, then
automatically exit Program Mode and
return to Normal Mode.
sound five (5) quick-beeps, then
automatically exit Program Mode and
return to Normal Mode.
To enter Program Mode, return to Step 1.
You may press “CLR” key anytime to exit
You may press “CLR” key anytime to exit
Program Mode and return to Normal Mode.
Under Programming Mode, you may perform the
following settings:
following settings:
Open or Close the VC100 Valve Controller
Storing, change, or remove Telephone
Numbers
Numbers
Test Dialling and Voice (from Remote
Phone)
Phone)
Test Voice (locally)
Turn OFF or ON automatic valve operations
Range Testing for valves and sensors
Changing Password
Storing Phone Numbers
Step 1: With Dialer already set to Programming
Mode, press “SET” key.
Step 2: Select your Dialling Priority Order Number 1
through 6. Then press the “#” key.
NOTE:
A maximum of five (5)
CELL PHONE
NUMBERS ONLY
numbers may be stored in
priority order. You may store less than five
numbers.
numbers.
1, 2, 3, 4, and 5 represent the priority
number of the five telephone numbers
respectively.
respectively.
The VHS-1050 will automatically dial in
sequence of the stored cell phone numbers.
Step 3: Key in phone number (maximum 20 digits),
then follow by the “SET” key to complete entry.
NOTE:
then follow by the “SET” key to complete entry.
NOTE:
The “*” may be used to delay dialing for
three (3) seconds. If more delay time is
required, pressing an additional “*” will
allow an additional three second delay
time. You may press “*” as often as
required.
required, pressing an additional “*” will
allow an additional three second delay
time. You may press “*” as often as
required.
Changing Phone Numbers
To change the telephone numbers, follow the steps
in Storing Telephone Numbers described in previous
section, then enter the new telephone numbers.
This will override the numbers previously
programmed.
in Storing Telephone Numbers described in previous
section, then enter the new telephone numbers.
This will override the numbers previously
programmed.
Clear Phone Numbers
To delete the telephone numbers, follow the steps
as in Storing Telephone Numbers described in
previous section and press “SET” without entering
any new phone numbers.
as in Storing Telephone Numbers described in
previous section and press “SET” without entering
any new phone numbers.
SET + 1~6 + SET
Successful deletion is indicated by a long beep,
followed by Power LED Red lights ON.
NOTE:
followed by Power LED Red lights ON.
NOTE:
For Storing, Changing or Removing
telephone numbers, a key-press interval of
five (5) seconds allowed.
If time is exceeded, or an entry is made in
error, the unit will automatically abort the
process and emit quick four (4) beeps,
indicating return to Program Mode.
five (5) seconds allowed.
If time is exceeded, or an entry is made in
error, the unit will automatically abort the
process and emit quick four (4) beeps,
indicating return to Program Mode.
To exit Programming Mode and return to
Normal Mode, press “CLR” key.