Vital Home Systems LLC 1050 Benutzerhandbuch
P a g e
| 5
© 2015 Vital Home Systems
Range Testing
Step 1: With the Dialer in Programming Mode,
press “Test” key followed by “8.”
The Power LED Red will flash, indicating that it
has entered Range-Test Mode.
The Power LED Red will flash, indicating that it
has entered Range-Test Mode.
Step 2: Press Sensor Test button. The Power LED
Red flashes ON for one (1) second then a long
beep will sound, indicating that signal has been
successfully received at this distance range.
The Dialer LED will also flash ON, enabling the
person testing the range from afar to see the
condition in case the beep cannot be heard.
beep will sound, indicating that signal has been
successfully received at this distance range.
The Dialer LED will also flash ON, enabling the
person testing the range from afar to see the
condition in case the beep cannot be heard.
NOTE:
Once a sensor has been successfully
Learned-In, the Dialer LED will stay lit for
another 60 seconds to allow you to Learn-In
the next one.
another 60 seconds to allow you to Learn-In
the next one.
Once in Range-Test Mode, if a key is not
pressed for 30 minutes, the Dialer will
sound five (5) quick-beeps then
automatically exit Range-Test Mode and
return to Program Mode.
sound five (5) quick-beeps then
automatically exit Range-Test Mode and
return to Program Mode.
You may exit Range-Test Mode to return to
Programming Mode anytime by pressing
“CLR” key.
“CLR” key.
To exit Programming Mode and return to
Normal Mode, press “CLR” key.
To enter Range-Test Mode, return to
Step 1.
Change Password
Step 1: With the Dialer in Programming Mode,
enter the Old PIN number followed by the
“CLR” key. A one-second beep will emit,
indicating that you have entered Change –
Password Mode.
“CLR” key. A one-second beep will emit,
indicating that you have entered Change –
Password Mode.
Step 2: Press the New PIN number followed by the
“SET” key. A one-second beep will be emitted
indicating that the password change was
successful.
indicating that the password change was
successful.
NOTE:
A key-press interval of five (5) seconds is
allowed; if five seconds are exceeded before
the next key-press or incorrect entry, it will
automatically abort the process. A quick
four-beep sound will be emitted to indicate
return to Program Mode.
the next key-press or incorrect entry, it will
automatically abort the process. A quick
four-beep sound will be emitted to indicate
return to Program Mode.
To enter Change-Password Mode, return to
Step 1.
You may exit Change-Password Mode
anytime by pressing “CLR” key.
To exit Programming Mode and return to
Normal Mode, press “CLR” key.
Exit Programming Mode
Press “CLR” key to exit the Programming Mode and
return to Normal Mode.
return to Normal Mode.
Recording Custom Audio
The 1050 Control Panel allows the user to create a
10 second custom audio recording that will play as
part of the message when a leak is detected. Vital
Home Systems recommends recording the 1050
location such as an address, unit number or building
number to provide unique ID for the system. To do
the custom recording:
Press and hold the SET button for 5 Seconds, when
you hear the beep begin speaking. When done
release the SET button. We suggest you speak about
4 inches away from the mic on the panel face clearly
and distinctly. To play back the recording press SET
+ 1. To re-record. Repeat the process.
10 second custom audio recording that will play as
part of the message when a leak is detected. Vital
Home Systems recommends recording the 1050
location such as an address, unit number or building
number to provide unique ID for the system. To do
the custom recording:
Press and hold the SET button for 5 Seconds, when
you hear the beep begin speaking. When done
release the SET button. We suggest you speak about
4 inches away from the mic on the panel face clearly
and distinctly. To play back the recording press SET
+ 1. To re-record. Repeat the process.
Reset Dialer to Default Settings
Step 1: Remove all power sources, including AC
power adaptor and battery. (To remove the
battery remove the 4 black feet and unscrew
the 4 case screws. Be careful not to over
tighten the screws when putting back together
so as not to strip the screw holes. Unplug the
battery from the PC board).
battery remove the 4 black feet and unscrew
the 4 case screws. Be careful not to over
tighten the screws when putting back together
so as not to strip the screw holes. Unplug the
battery from the PC board).
Step 2: With the panel apart keeping the “CLR” key
pressed, plug in the AC power adaptor. A long
one-second beep will emit indicating that the
Panel has been successfully reset to Default
Settings.
one-second beep will emit indicating that the
Panel has been successfully reset to Default
Settings.
Step 3: Plug the battery back in and close the case
carefully not to over tighten the screws.
NOTE:
Under Factory Default Setting –
Under Factory Default Setting –
PIN code is set as “0000”
VHS-1050 is cleared of all telephone
numbers.
numbers.
VHS-1050 is cleared of all sensor devices.