ALVOR ELECTRONICS INC. LIGHT10 Benutzerhandbuch
The TOUCH can be pressed at its ON side or at its OFF side.
The ON side side gives access to a sequence of 4 commands and the OFF side to a sequence of 3 commands.
Keeping pressed, either, the ON side or the OFF side of a TOUCH, will start the execution of the corresponding
sequence of commands.
sequence of commands.
The execution of the subsequent command in a sequence, cancel the effect of the execution of the precedent
command.
command.
So, when you release the TOUCH, the last executed command is the one that will remain active.
So, in a few words, you press the TOUCH, keep it pressed till the desired command shows up, then release the
TOUCH.
TOUCH.
While keeping pressed the TOUCH, the sequence of execution of the commands is as follow:
ON SIDE:
1 second: The LAMP goes ON. You should then release the TOUCH.
5 seconds: Command SLEEPY is started. The LAMP will blink, then goes ON for 10 minutes and then goes OFF. As
soon as the lamp blinks, you should release the TOUCH.
soon as the lamp blinks, you should release the TOUCH.
10 seconds: Command DIMMER is started. Then, you should release the TOUCH. The LAMP will go continually
from almost OFF to BRIGHT, then to almost OFF again, in 9 steps of 1 second each. When you consider
convenient the brightness level showed by the LAMP, you should press either side of the TOUCH momentarily (1
second). DIMMER command execution will stop. The brightness showed by the LAMP at this moment is
MEMORIZED at the POWER UNIT. It will be the brightness level showed by the lamp in the future, until modified
again by a new execution of the DIMMER command. In case of loss of energy at the POWER UNIT, when energy
returns the LAMP will show the MEMORIZED brightness level.
from almost OFF to BRIGHT, then to almost OFF again, in 9 steps of 1 second each. When you consider
convenient the brightness level showed by the LAMP, you should press either side of the TOUCH momentarily (1
second). DIMMER command execution will stop. The brightness showed by the LAMP at this moment is
MEMORIZED at the POWER UNIT. It will be the brightness level showed by the lamp in the future, until modified
again by a new execution of the DIMMER command. In case of loss of energy at the POWER UNIT, when energy
returns the LAMP will show the MEMORIZED brightness level.
60 seconds: Command TOGGLE DIMMER is started. The LAMP will go ON for 10 seconds. Then the LAMP will
start blinking, once at each 2 seconds, during 30 seconds. If during this 30 seconds window, you press either side
of the TOUCH momentarily (1 second), the TOGGLE DIMMER command execution will be aborted and no action
will be taken. Else, at the end of the 30 seconds window, the TOGGLE DIMMER command is executed. If the
DIMMER command was active, it becomes inactive. If the DIMMER command was inactive, it becomes active.
The DIMMER command must be inactive for LAMPS that are not dimmable, like the gas discharge lamps and the
majority of the LED lamps. The incandescent LAMPS are dimmable as well as some LED lamps. Attention, at the
production line, the DIMMER command is programmed to its inactive state.
start blinking, once at each 2 seconds, during 30 seconds. If during this 30 seconds window, you press either side
of the TOUCH momentarily (1 second), the TOGGLE DIMMER command execution will be aborted and no action
will be taken. Else, at the end of the 30 seconds window, the TOGGLE DIMMER command is executed. If the
DIMMER command was active, it becomes inactive. If the DIMMER command was inactive, it becomes active.
The DIMMER command must be inactive for LAMPS that are not dimmable, like the gas discharge lamps and the
majority of the LED lamps. The incandescent LAMPS are dimmable as well as some LED lamps. Attention, at the
production line, the DIMMER command is programmed to its inactive state.
OFF SIDE:
1 second: The LAMP goes OFF.
50 seconds: INTRODUCE command is started. The LAMP goes ON for 10 seconds. You should then release the
TOUCH, as soon as the lamp goes ON. Then the LAMP will start blinking once each second, during 30 seconds. If
TOUCH, as soon as the lamp goes ON. Then the LAMP will start blinking once each second, during 30 seconds. If