Viking CTG-1 Benutzerhandbuch
F
F
e
e
a
a
t
t
u
u
r
r
e
e
s
s
O
O
v
v
e
e
r
r
v
v
i
i
e
e
w
w
Connect the CTG-1 between your phone system and your paging amplifier as shown in the diagram below. The factory
installed rechargeable 9V battery will maintain the clock time for over 8 hours.
installed rechargeable 9V battery will maintain the clock time for over 8 hours.
IMPORTANT: The CTG-1 leaves the factory with the battery backup DIP switch turned OFF to avoid discharging
the battery during shipment. The battery backup DIP switch MUST be set to ON (see Programming section J) to
maintain clock time during a power outage.
the battery during shipment. The battery backup DIP switch MUST be set to ON (see Programming section J) to
maintain clock time during a power outage.
Clock and Event Time Setting Buttons: Press
the + or -/CANCEL buttons to increase or
decrease time. The -/CANCEL switch is also
used to cancel an alert tone event when review-
ing programming.
the + or -/CANCEL buttons to increase or
decrease time. The -/CANCEL switch is also
used to cancel an alert tone event when review-
ing programming.
Alert Tones Programming Buttons: After set-
ting an event time, press SINGLE, DOUBLE or
TRIPLE to program 1, 2 or 3 alert bongs/buzzer
sounds for that event time.
ting an event time, press SINGLE, DOUBLE or
TRIPLE to program 1, 2 or 3 alert bongs/buzzer
sounds for that event time.
Secondary Button Functions While in the SET
DAY Mode: The SINGLE button is used to select
between day (1-7) or on/off. The DOUBLE but-
ton is used as a one time setup to program
today’s day of the week.
DAY Mode: The SINGLE button is used to select
between day (1-7) or on/off. The DOUBLE but-
ton is used as a one time setup to program
today’s day of the week.
12 - Common
11- Emergency Siren (Yelp): Continuous while
shorted to pin 12 (common).
shorted to pin 12 (common).
10 - Evacuation Sound (Temporal Slow Whoop):
Continuous while shorted to pin 12 (common).
Continuous while shorted to pin 12 (common).
9 - Doorbell Chime Sound (Ding Dong): One
chime per closure.
chime per closure.
8 - N.O.
7 - COM Relay Contact
6 - N.C.
7 - COM Relay Contact
6 - N.C.
5 - N.O.
4 - COM Relay Contact
3 - N.C.
4 - COM Relay Contact
3 - N.C.
1 & 2 - 600 Ohm Audio Out Pair: Line level output,
connect to input of paging amplifier.
connect to input of paging amplifier.
PM
TIME
/ CANCEL
-
+
MODE
ALERT TONES
SINGLE
DOUBLE
TRIPLE
VIKING
©
MODEL CTG-1
LOCK
SET DAY
SET TIME
SET EVENTS
REVIEW/CANCEL
REVIEW/CANCEL
CLOCK CONTROLLED
TONE GENERATOR
VOL
9V BATTERY
BACKUP
1 2 3 4 5 6 7 8 9 10 11 12
S1
1
2
on
1
2
ON
ON
OFF
DIP Switches: See
Programming section
J.
Programming section
J.
Mode Button: Press to place the CTG-1 in the
Lock, Set Time, Set Day, Set Events or
Review/Cancel modes.
Lock, Set Time, Set Day, Set Events or
Review/Cancel modes.
9V Battery Backup Connection: A standard
rechargeable (NiMh) 9V battery is installed to
maintain the clock time during power outages.
rechargeable (NiMh) 9V battery is installed to
maintain the clock time during power outages.
CTG-1 Output Volume Control: Turn clockwise
to increase volume of alert bongs/buzzer sounds,
emergency and door bell (chime) sounds (see
diagram below).
to increase volume of alert bongs/buzzer sounds,
emergency and door bell (chime) sounds (see
diagram below).
1 2 3 4 5 6 7 8 9 10
PAGING - LOUD RINGING
AMPLIFIER SYSTEM
VIKING
ELECTRONICS
HUDSON, WI 54016
VIKING
©
MODEL PA-2A
POWER 13.8V
AC
1
2
3
4
5
6
7
8
9 10
NIGHT
TRANSFER
PA
G
ING
HORN
600 OHM
AUDIO OU
T
TRUNK OR
P
AGING P
ORT
DR
Y
CONT
ACT
CLOSURE IN
PAGING
VOLUME
RINGING
VOLUME
VOLUME
MAX
MIN
MAX
MIN
1 - 3
4 - 6
RINGING LINES
AUDIO LOADING
TALK BATTERY
ALERT TONE
WARBLE / CHIME
1 2 3 4 5
PM
TIME
/ CANCEL
-
+
MODE
ALERT TONES
SINGLE
DOUBLE
TRIPLE
VIKING
©
MODEL CTG-1
LOCK
SET DAY
SET TIME
SET EVENTS
REVIEW/CANCEL
CLOCK CONTROLLED
TONE GENERATOR
VOL
9V BATTERY
BACKUP
1 2 3 4 5 6 7 8 9 10 11 12
Paging port
output of
PABX/KSU
PA-2A Paging/Loud Ringing
Amplifier System
Input of
Paging Amp
-or-
Common
Siren
Evacuation Signal
Doorbell
Dry Contact Closures from Alarm
Equipment, Doorbell Switch, Etc.
Display:
Shows
clock, event time
and mode settings.
and mode settings.
* Note: When the buzzer alert tone is programmed, a double or
triple programmed event will be sounded twice, approximately
three seconds apart.
triple programmed event will be sounded twice, approximately
three seconds apart.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n