Viking CTG-1 Benutzerhandbuch

A. Setting the Clock Time

1. Press the MODE button repeatedly until the SET TIME indicator lights.
2. Increase or decrease the clock time by pressing the + or -/CANCEL button until the desired time is displayed.
3. Leave the set time mode by pressing the MODE button.
Note: Either the + or -/CANCEL button MUST be pressed at least once prior to leaving the set time mode. The clock will then start to run the moment you leave
the set time mode, allowing you to synchronize the

CTG-1 with your building clocks.

B. Setting the Day of the Week

Note: This step is only required if you want to turn off the Alert Tones on certain days of the week.
1. Press the MODE button repeatedly until the SET DAY indicator lights.
2. A flashing “A” indicates all 7 days of the week are “on” and today’s day has not been set. The day of the week has already been set if a flashing number

(1-7) and “on” or “of” are displayed.

3. Select today’s day of the week using the TIME (+ and -/CANCEL) buttons. As a general rule, Sunday is day 1 and Saturday is day 7. When today’s day of

the week is flashing on the display, set it by pressing the DOUBLE alert tone button. Today’s day number and “on” will now be displayed.

Note: The day of the week setting and turning the alert tones off on specific days of the week is a one time set up and does not need to be reset unless you
have experienced a brown out long enough to discharge the 9V battery backup (approximately 8 hours). To reset the day of the week and turn off tones on spe-
cific days of the week, you must power down the

CTG-1, set DIP switch 1 to OFF, power up the CTG-1 and repeat steps 1-3 above. If you had alert tones turned

off on specific days of the week, repeat steps 1-4 in section

C below. When finished, set DIP switch 1 back to ON.

C. Turning the Alert Tones On/Off for Specific Days of the Week

D. Setting Timed Alert Tones

1. Press the MODE button repeatedly until the SET EVENTS indicator lights.
2. Increase or decrease the event time by pressing the TIME (+ or -/CANCEL) button until the desired time is shown.
3. Move DIP switch 2 to OFF for bong alert tones or ON for buzzer alert tones (see Programming section J).
4. Press one of the single, double, or triple ALERT TONES buttons to program the number of alert tones you wish to output at the specific event time. A single,

double, or triple confirmation beep should be heard.

5. Repeat steps 2-4 for the remainder of your scheduled events.
Note: If more than 128 events have been entered, a long beep will be heard indicating that the event memory is full.

E. Reviewing and/or Cancelling Timed Alert Tones

1. Press the MODE button repeatedly until the REVIEW/CANCEL indicator lights.
2. Press one of the ALERT TONES buttons (single, double, or triple) repeatedly to rotate through the event times associated with that alert tone button. A red

LED at the bottom right corner of the time display will light to indicate a buzzer event time (versus a bong event).

Note: Event times are stored in the order of programming, not chronologically.
3. Press the -/CANCEL button to permanently cancel an event tone. A single acknowledgement tone will be heard. The next consecutive event for that

specific alert tone will then be displayed.

4. Repeat steps 2-3 as needed to remove the events to be cancelled.
5. When all events for a given alert tone have been cancelled, the display shows three dashes (- - -).

F. Adjusting Output Volume

1. Short pins 9 and 12 together momentarily. The doorbell sound will then chime once.
2. Adjust the volume control potentiometer (see Installation).
3. Repeat steps 1-2 until the desired volume is achieved.

G. Activating Contact Closure Alarm Tones

To activate different sounds, short the corresponding pins with a dry contact closure as
shown right (see Installation, section A). Note: The evacuation sound and siren will be
repeated continuously, as long as the closures are maintained.

1. Press the MODE button repeatedly until the SET DAY indicator lights. The current day of the week and “on” or “of” will be displayed. “on” = alert tones are

ON and “of” = alert tones are OFF for that day of the week .

2. Pressing the SINGLE button will toggle between flashing the day of the week and flashing “on” or “of”. The flashing portion of the display is the section that

can be changed.

3. With the day of the week flashing, use the TIME (+ and -/CANCEL) buttons to select the day of the week you would like to set to ON or OFF. When the

correct day of the week is displayed, press the SINGLE button to flash “on” or “of”. The day can then be set to ON or OFF by using the TIME (+ and
-/CANCEL) buttons.

4. Review your day of the week programming by pressing the SINGLE button until the weekday (1-7) is flashing, then increment through each day of the week

with the TIME (+) button and monitor each day for its on or off setting. Exit the SET DAY mode by simply pressing the MODE button.

When finished programming, press the MODE button until the LOCK indicator lights. In the lock mode, the time and alert tone keys will be disabled and the cur-
rent time will be displayed with the colon flashing once per second.

H. Locking the CTG-1 for Operation

Sound

Doorbell (Ding Dong)

Evacuation Sound (Slow Whoop)

Siren (Yelp)

Short Pins...

...9 to 12

...10 to 12

...11 to 12

Turn DIP switch 1 OFF. Unplug the CTG-1 from power. Pause a few seconds and then plug the CTG-1 back in. Push the CANCEL and SINGLE buttons at the
same time and release them. Repeat, and after releasing the buttons the second time a long beep will be heard indicating that the CTG-1’s memory has been
cleared. Turn DIP switch 1 back ON to enable battery backup. Note: After completing this procedure, it will be necessary to reset the clock time (see
Programming section A), and if enabled, the day of the week (see Programming section B) and alert tones on/off (see Programming section C).

I. Clearing the Alert Tone Memory