Wayne-Dalton 341785 Benutzerhandbuch
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.
To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at
www.wayne-dalton.com
28
Tools Needed:
aDjusTMENTs TO ThE sPRINGs,
ENsuRE yOu’RE WINDING IN ThE
PROPER DIRECTION as sTaTED IN ThE
INsTallaTION INsTRuCTIONs.
OThERWIsE ThE sPRING FITTINGs May
RElEasE FROM sPRING IF NOT WOuND
IN ThE PROPER DIRECTION aND COulD
REsulT IN sEVERE OR FaTal INjuRy.
ENsuRE yOu’RE WINDING IN ThE
PROPER DIRECTION as sTaTED IN ThE
INsTallaTION INsTRuCTIONs.
OThERWIsE ThE sPRING FITTINGs May
RElEasE FROM sPRING IF NOT WOuND
IN ThE PROPER DIRECTION aND COulD
REsulT IN sEVERE OR FaTal INjuRy.
Now, lift door and check it’s balance.
adjust, if door lifts by itself (hard to pull
down) or if door is difficult to lift (easy
to pull down). loosen set screws before
adjusting the number of turns of spring
tension. To adjust spring(s), only add
or remove 1/4 turn on the springs at a
time. adjust both sides equally. Tighten
set screws once adjustments have been
completed.
adjust, if door lifts by itself (hard to pull
down) or if door is difficult to lift (easy
to pull down). loosen set screws before
adjusting the number of turns of spring
tension. To adjust spring(s), only add
or remove 1/4 turn on the springs at a
time. adjust both sides equally. Tighten
set screws once adjustments have been
completed.
IMPORTANT:
DO NOT aDD OR REMOVE
MORE ThaN 1 sPRING TuRN FROM
sPECIFIED aMOuNT. IF ThE DOOR sTIll
DOEs NOT OPERaTE EasIly, lOWER
ThE DOOR TO ThE ClOsED POsITION,
uNWIND sPRING(s) TO zERO, aND
REChECk ThE FOllOWING ITEMs:
sPECIFIED aMOuNT. IF ThE DOOR sTIll
DOEs NOT OPERaTE EasIly, lOWER
ThE DOOR TO ThE ClOsED POsITION,
uNWIND sPRING(s) TO zERO, aND
REChECk ThE FOllOWING ITEMs:
1.) Check the door for level.
2.) Check the
torsion spring tube
and
flagangles for level and plumb.
3.) Check the distance between the
flagangles - must be door width
plus 3-3/8” to 3-1/2”.
flagangles - must be door width
plus 3-3/8” to 3-1/2”.
4.) Check the counterbalance cables
for equal tension - adjust if
for equal tension - adjust if
necessary.
5.) Rewind the spring(s).
6.) Make sure door isn’t rubbing on
jambs.
Rear Support
PERFORaTED aNGlE
(3) 5/16”
bOlTs & NuTs
bOlTs & NuTs
hORIzONTal TRaCk
bOlT MusT ExTEND INTO
ThE TRaCk TO sERVE as
a ROllER sTOP
aNGlE bRaCE
PERFORaTED aNGlE
bOlTED usING (2) 5/16”
x 1-5/8” hEx hEaD laG
sCREWs TO CEIlING
MEMbER aND PaRallEl
TO DOOR
sOuND FRaMING MEMbERs
sOuND FRaMING MEMbERs
hORIzONTal TRaCk
aNGlE bRaCE
bOlT MusT ExTEND INTO
ThE TRaCk TO sERVE as
a ROllER sTOP
PERFORaTED aNGlE
bOlTED usING (2) 5/16”
x 1-5/8” hEx hEaD laG
sCREWs TO CEIlING
MEMbER aND PaRallEl
TO DOOR
jaMb
WEaThER
sEal
PERMaNENTly aTTaChED
WEaThER sEal