BlueStar RNB364GHCV1 Installationsanweisungen
P/N 750301 Page 10
factory. These adjustments may need to
be redone and/or fine tuned by the in-
staller. These adjustments are normal.
They are the responsibility of the qualified
installer and are not covered by your war-
ranty.
be redone and/or fine tuned by the in-
staller. These adjustments are normal.
They are the responsibility of the qualified
installer and are not covered by your war-
ranty.
16. A gas conversion performed in the field
may void your warranty. Contact your
dealer for information regarding the con-
version from one type of gas supply to
another.
dealer for information regarding the con-
version from one type of gas supply to
another.
ELECTRICAL CONNECTIONS
1. The installation of this appliance must
conform with all applicable local codes.
In the absence of local codes, the installa-
tion must conform to the latest level of the
National Electric Code, ANSI/NFPA 70.
In the absence of local codes, the installa-
tion must conform to the latest level of the
National Electric Code, ANSI/NFPA 70.
2. This appliance is equipped with a standard
three prong polarized, NEMA 5-15P line
cord to be plugged into a 120Volt 15 Amp
outlet.
cord to be plugged into a 120Volt 15 Amp
outlet.
3. Removing the grounding prong from the
plug will void the manufacturer’s war-
ranty.
ranty.
4. The cord exits the appliance at the lower
rear toward the right (viewed from front)
side.
side.
5. If the electrical supply is not turned on or
is interrupted the appliance will not oper-
ate.
ate.
6. The applicable wiring diagram for this
appliance is affixed to the appliance.
7. The
circuit
where
you plug your appliance
must be grounded and polarized.
8. We recommend the circuit for your appli-
ance be a non-GCFI dedicated line.
9. It is recommended that your circuit never
include a microwave oven.
WARNING
This appliance is equipped with a three-
pronged grounding plug for your protec-
tion against shock hazard and should be
plugged directly into a properly grounded
receptacle. Do NOT cut or remove the
grounding prong from this plug.
If the appliance is not grounded or its po-
larity is reversed severe shock hazards can
exist.
VENTILATION
Proper ventilation is highly important for
good operation. This appliance must be in-
stalled under a properly designed canopy
hood. The hood should be six inches [150
mm] wider than the appliance.
A strong exhaust fan can create a vacuum in
the room. For proper air balance work with
your dealer and/or contactor to properly size
your hood and its exhaust fan. It is recom-
mended that your exhaust hood be powerful
enough to move a minimum of 300 cfm.
pronged grounding plug for your protec-
tion against shock hazard and should be
plugged directly into a properly grounded
receptacle. Do NOT cut or remove the
grounding prong from this plug.
If the appliance is not grounded or its po-
larity is reversed severe shock hazards can
exist.
VENTILATION
Proper ventilation is highly important for
good operation. This appliance must be in-
stalled under a properly designed canopy
hood. The hood should be six inches [150
mm] wider than the appliance.
A strong exhaust fan can create a vacuum in
the room. For proper air balance work with
your dealer and/or contactor to properly size
your hood and its exhaust fan. It is recom-
mended that your exhaust hood be powerful
enough to move a minimum of 300 cfm.
IMPORTANT
ALL GAS BURNERS NEED SUFFICIENT AIR
TO OPERATE AND LARGE OBJECTS SHOULD
NOT BE PLACED IN FRONT OF THIS APPLI-
ANCE WHICH WOULD OBSTRUCT THE AIR
FLOW THROUGH THE FRONT. OBJECTS
SHOULD NOT BE PLACED ON THE REAR
BACKGUARD WHILE IN USE. THIS COULD
OBSTRUCT THE VENTING SYSTEM OF THE
OVEN’S FLUE PRODUCTS.
TO OPERATE AND LARGE OBJECTS SHOULD
NOT BE PLACED IN FRONT OF THIS APPLI-
ANCE WHICH WOULD OBSTRUCT THE AIR
FLOW THROUGH THE FRONT. OBJECTS
SHOULD NOT BE PLACED ON THE REAR
BACKGUARD WHILE IN USE. THIS COULD
OBSTRUCT THE VENTING SYSTEM OF THE
OVEN’S FLUE PRODUCTS.
INSTALLATION