Broan B5630SS Installationsanweisungen
MODELS B5630SS • B5636SS • B5730SS • B5736SS
Page 2
INSTALL THE DUCTWORK
(Ducted Hoods Only)
(Ducted Hoods Only)
1. Decide where
the ductwork
will run
between the
hood and the
outside.
will run
between the
hood and the
outside.
2. A straight, short
duct run will
allow the hood
to perform most
efficiently.
allow the hood
to perform most
efficiently.
3. Long duct
runs, elbows
and transitions
will reduce the
performance of
the hood. Use as few of them as possible. Larger ducting
may be required for best performance with longer duct runs.
and transitions
will reduce the
performance of
the hood. Use as few of them as possible. Larger ducting
may be required for best performance with longer duct runs.
4. Install wall cap or roof cap. Connect round metal ductwork
to cap and work back towards the hood location. Use duct
tape to seal the joints between ductwork sections.
tape to seal the joints between ductwork sections.
MEASURE THE INSTALLATION
The minimum hood distance above cooktop MUST NOT BE
LESS than 30”.
A maximum of 36” above cooktop is highly recommended for
best capture of cooking impurities.
LESS than 30”.
A maximum of 36” above cooktop is highly recommended for
best capture of cooking impurities.
Distances over 36” are at the installer and users discretion;
providing that the ceiling height permits.
providing that the ceiling height permits.
PREPARE THE HOOD
6”
ROUND
DUCT
ROOF
CAP
ROUND
ELBOW
30”
TO
36”
ABOVE
COOKING
SURFACE
WALL
CAP
HOOD
DECORATIVE
FLUE
HOOD
12
1
/
2
”
TO
CENTER
OF
BRACKET
HOLES
ROUND
ELBOW
HOOD
MOUNTING
BRACKET
30”
TO
36”
ABOVE
COOKING
SURFACE
*
3¼”
DECORATIVE
FLUE
6”
ROUND
DUCT
ROOF
CAP
WALL
CAP
Unpack hood and check contents. You should receive:
1 - Hood
1 - Glass Canopy (Models B5630SS & B5636SS)
1 - Metal Canopy (Models B5730SS & B5736SS)
1 - Decorative Flue Assembly
1 - Damper / Duct Connector
1 - Lower Flue Mounting Bracket
1 - Upper Flue Mounting Bracket
1 - Hood Mounting Bracket
2 - Aluminum Grease Filters (installed in hood)
1 - Parts Bag containing:
1 - Hood
1 - Glass Canopy (Models B5630SS & B5636SS)
1 - Metal Canopy (Models B5730SS & B5736SS)
1 - Decorative Flue Assembly
1 - Damper / Duct Connector
1 - Lower Flue Mounting Bracket
1 - Upper Flue Mounting Bracket
1 - Hood Mounting Bracket
2 - Aluminum Grease Filters (installed in hood)
1 - Parts Bag containing:
8 - Mounting Screws (#8 x 3/8” Pan Head)
7 - Mounting Screws (#8 x 1-1/2” Flat Head)
4 - Mounting Screws (M4 x 1.0 Flat Head)
7 - Drywall Anchors
2 - Washers
4 - Decorative Washers
7 - Mounting Screws (#8 x 1-1/2” Flat Head)
4 - Mounting Screws (M4 x 1.0 Flat Head)
7 - Drywall Anchors
2 - Washers
4 - Decorative Washers
1 - Installation Manual
7 MOUNTING
SCREWS
(#8 X 1-1/2”
Flat Head)
7 DRYWALL
ANCHORS
8 MOUNTING
SCREWS
(#8 x 3/8”
Pan Head)
SCREWS
(#8 x 3/8”
Pan Head)
DECORATIVE FLUE
2 WASHERS
UPPER
FLUE MOUNTING
BRACKET
HOOD
MOUNTING
BRACKET
LOWER
FLUE MOUNTING
BRACKET
DAMPER / DUCT
CONNECTOR
4 MOUNTING
SCREWS
(M4 X 1.0”
Flat Head)
SCREWS
(M4 X 1.0”
Flat Head)
4 DECORATIVE
WASHERS