NEC NP52G Benutzerhandbuch
. Usng On-Screen Menu
Settng ID to the Projector [CONTROL ID]
(Avalable only when the optonal remote control NP0RC s used)
(Avalable only when the optonal remote control NP0RC s used)
You can operate multiple projectors separately and independently with a single remote control that has the CON-
TROL ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors
together using the single remote control. To do so, you have to assign an ID number to each projector.
TROL ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors
together using the single remote control. To do so, you have to assign an ID number to each projector.
CONTROL ID NUMBER ......Select a number from 1 to 254 you wish to assign to your projector.
CONTROL ID ......................Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID
CONTROL ID ......................Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID
setting.
ID DISPLAY ........................This option turns on or off the ID number which is displayed when the ID SET button on the
remote control is pressed.
NOTE:
• Selecting [ON] for [CONTROL ID] will make the remote control supplied with the projector inoperable. The buttons on the
projector cabinet can be used. Optional remote control NP01RC does not have the CONTROL ID function and therefore cannot
operate the projector once a Control ID is set.
• Pressing and holding the ENTER button on the projector cabinet for 10 seconds will display the menu for canceling the Con-
trol ID.
• Your setting will not be affected even when [RESET] is done from the menu.
Assgnng or Changng the Control ID
1. turn on the projector.
2. Press the id set button on the remote control (nP02rC).
The CONTROL ID screen will be displayed.
1. turn on the projector.
2. Press the id set button on the remote control (nP02rC).
The CONTROL ID screen will be displayed.
If the projector can be operated with the current remote control ID, the [ACTIVE] will be displayed. If the pro-
jector cannot be operated with the current remote control ID, the [INACTIVE] will be displayed. To operate the
inactive projector, assign the control ID used for the projector by using the following procedure (Step 3).
inactive projector, assign the control ID used for the projector by using the following procedure (Step 3).
3. Press one of numeric keypad buttons while pressing and holding the id set button on the remote con-
trol (nP02rC).
OFF
ON
COMPUTER
VIDEO
S-VIDEO
VIEWER NETWORK
HDMI
PIP
MAGNIFY
VOLUME
PICTURE
LAMP MODE
ASPECT
AV-MUTE
3D REFORM
FREEZE
ID SET
LENS SHIFT
FOCUS
/ZOOM
HELP
PAGE
MENU
L-CLICK
R-CLICK
EXIT
COMPONENT
AUTO ADJ.
ENTER
UP
DOWN
POWER
ID
ID
1
2
3
1
3
2
4
6
5
7
9
8
0
CLEAR
OFF
ON
COMPUTER
VIDEO
S-VIDEO
VIEWER NETWORK
HDMI
PIP
MAGNIFY
VOLUME
PICTURE
LAMP MODE
ASPECT
AV-MUTE
3D REFORM
FREEZE
ID SET
LENS SHIFT
FOCUS
/ZOOM
HELP
PAGE
MENU
L-CLICK
R-CLICK
EXIT
COMPONENT
AUTO ADJ.
ENTER
UP
DOWN
POWER
ID
ID
1
2
3
1
3
2
4
6
5
7
9
8
0
CLEAR
example:
To assign "3", press the "3" button on the remote control.
No ID means that all the projectors can be operated together with a single remote
No ID means that all the projectors can be operated together with a single remote
control. To set "No ID", enter "000" or press the CLEAR button.
TIP: The range of IDs is from 1 to 254.
4. release the id set button.
The updated CONTROL ID screen will be displayed.
NOTE: The IDs can be cleared in a few days after the batteries are run down or removed.
The updated CONTROL ID screen will be displayed.
NOTE: The IDs can be cleared in a few days after the batteries are run down or removed.