Panasonic AJ-HD150 User Manual
– 51 –
Setup menus
SYSTEM menu
<SYSTEM>
Item
Setting
No.
Superimposed
No.
Superimposed
Description
display
display
00
WFM SEL
0000
CTL
0001
TC
0002 VIDEO
0003
SYNC
0004
RF-L
0005
RF-R
0006
ENV-L
0007
ENV-R
10
ENCODER
0000
REMOTE
REMOTE
0001
LOCAL
SEL
11
SYS SC/H
0000
REMOTE
0001
LOCAL
12
SYS H
0000
–1100
(HD)*1
:
:
1100
0
:
:
2200
1100
13
V PHASE
0000
–500
(HD)*1
:
:
0500
0
:
:
1000
500
14
SYS SC
0000
–108
(SD)*
2
:
:
0108
0
:
:
0216
108
The underline on the setting item denotes the initial setting.
*
1
: With the HD output (HD tape playback or up-conversion output)
*
2
: With the SD output (SD tape playback or down-conversion output)
This selects the signal to output from the VIDEO OUT 2
connector.
0: The CTL signal is output.
1: The TIME CODE signal is output.
2: The VIDEO OUT signal is output.
3: The SYNC signal is output.
4: The PB L RF signal is output.
5: The PB R RF signal is output.
6: The PB L ENV signal is output.
7: The PB R ENV signal is output.
<Note>
1. The settings can be changed at any time regardless of the
connector.
0: The CTL signal is output.
1: The TIME CODE signal is output.
2: The VIDEO OUT signal is output.
3: The SYNC signal is output.
4: The PB L RF signal is output.
5: The PB R RF signal is output.
6: The PB L ENV signal is output.
7: The PB R ENV signal is output.
<Note>
1. The settings can be changed at any time regardless of the
setup menu item No. 30 (MENU LOCK) setting.
2. The signals which are output during normal playback have
approximately the levels given below.
CTL: 0.1 to 0.3 Vp-p TC: 0.6 Vp-p
VIDEO: 1.0 Vp-p
CTL: 0.1 to 0.3 Vp-p TC: 0.6 Vp-p
VIDEO: 1.0 Vp-p
This selects whether the video output signal is to be adjusted
on the VTR or with the external encoder remote control.
0: Video output signals are adjusted with the external encoder
on the VTR or with the external encoder remote control.
0: Video output signals are adjusted with the external encoder
remote control.
1: Video output signals are adjusted on the VTR.
This sets whether the system phase is to be adjusted using
the unit’s controls or using the external encoder remote
control.
0: The external encoder remote control is used to adjust the
the unit’s controls or using the external encoder remote
control.
0: The external encoder remote control is used to adjust the
system phase.
1: The system phase is adjusted using the unit’s controls.
<Note>
This setting has no effect when LOCAL has been selected as
the SYSTEM menu item No.10 (ENCODER SEL).
<Note>
This setting has no effect when LOCAL has been selected as
the SYSTEM menu item No.10 (ENCODER SEL).
This enables the system phase to be adjusted in 13.5ns steps.
-: The phase is advanced.
+: The phase is delayed.
<Note>
If setting operation is performed, the setting value does not
return to factory (default) setting.
-: The phase is advanced.
+: The phase is delayed.
<Note>
If setting operation is performed, the setting value does not
return to factory (default) setting.
This enables the video system phase to be adjusted in 27ns
steps.
-: The phase is advanced.
+: The phase is delayed.
<Note>
In the case of the HD up-converter output from the SD
playback tape (when the option has been installed), the video
phase is fixed.
steps.
-: The phase is advanced.
+: The phase is delayed.
<Note>
In the case of the HD up-converter output from the SD
playback tape (when the option has been installed), the video
phase is fixed.
This enables the system phase to be adjusted in a total
variable range of +/-180 degrees or more.
-: The phase is advanced.
+: The phase is delayed.
<Note>
If setting operation is performed, the setting value does not
return to factory (default) setting.
variable range of +/-180 degrees or more.
-: The phase is advanced.
+: The phase is delayed.
<Note>
If setting operation is performed, the setting value does not
return to factory (default) setting.