Renesas rl78 User Manual

 

RL78/G1A 

 

CHAPTER  11   A/D  CONVERTER 

R01UH0305EJ0200  Rev.2.00 

 

 

376  

Jul 04, 2013 

 

<1>  In the stop status, the ADCE bit of A/D converter mode register 0 (ADM0) is set to 1, and the system enters the 

A/D conversion standby status. 

<2>  After the software counts up to the stabilization wait time

, the ADCS bit of the ADM0 register is set to 1 to 

place the system in the hardware trigger standby status (and conversion does not start at this stage).  Note that, 

while in this status, A/D conversion does not start even if ADCS is set to 1. 

<3>  If a hardware trigger is input while ADCS = 1, A/D conversion is performed on the analog input specified by the 

analog input channel specification register (ADS). 

<4>  When A/D conversion ends, the conversion result is stored in the A/D conversion result register (ADCR, ADCRH), 

and the A/D conversion end interrupt request signal (INTAD) is generated.  After A/D conversion ends, the next 

A/D conversion immediately starts. 

<5>  If a hardware trigger is input during conversion operation, the current A/D conversion is interrupted, and 

conversion restarts.  The partially converted data is discarded. 

<6>  When the value of the ADS register is rewritten or overwritten during conversion operation, the current A/D 

conversion is interrupted, and A/D conversion is performed on the analog input respecified by the ADS register.  

The partially converted data is discarded. 

<7>  When ADCS is overwritten with 1 during conversion operation, the current A/D conversion is interrupted, and 

conversion restarts.  The partially converted data is discarded. 

<8>  When ADCS is cleared to 0 during conversion operation, the current A/D conversion is interrupted, and the 

system enters the A/D conversion standby status.  However, the A/D converter does not stop in this status. 

<9>  When ADCE is cleared to 0 while in the A/D conversion standby status, the A/D converter enters the stop status.  

When ADCS = 0, inputting a hardware trigger is ignored and A/D conversion does not start. 

 

Note  If a high-accuracy channel is selected as the analog input channel:  Stabilization wait time = 0.5 

μ

s 

If a standard channel is selected as the analog input channel: 

Stabilization wait time = 2 

μ

s 

 

 

ADCE is set to 1.

<1>

ADCS is set to 1.

<2>

A hardware trigger 
is generated.

<3>

A hardware trigger is 
generated during A/D 
conversion operation.

<5>

A/D conversion 
ends  and the next 
conversion
starts.

<4>

ADS is rewritten during 
A/D conversion operation 
(from ANI0 to ANI1).

<6>

Conversion is 
interrupted 
and restarts.

Conversion is 
interrupted 
and restarts.

Conversion is 
interrupted and
restarts.

<4>

<4>

<4>

<4>

ADCS is overwritten 

with 1 during A/D 

conversion operation.

<7>

ADCS is cleared 

to 0 during A/D 

conversion operation.

ADCE is cleared to 0. <9>

ADCE

ADCS

ADS

INTAD

ADCR,

ADCRH

A/D

conversion

status

Hardware

trigger

Stop

status

ANI0

ANI1

The trigger is not

acknowledged.

Trigger

standby

status

The trigger is not

acknowledged.

Data 1
(ANI0)

Data 1
(ANI0)

Data 2
(ANI0)

Data 4
(ANI0)

Data 2
(ANI0)

Data 3
(ANI0)

Data 4
(ANI0)

Data 5
(ANI0)

Data 6
(ANI1)

Data 6
(ANI1)

Data 8
(ANI1)

Data 7
(ANI1)

Data 8
(ANI1)

Data 8
(ANI1)

Conversion

standby

Conversion

standby

Stop

status

Conversion

is interrupted.

<8>