Bosch ICP-CC488 User Manual
ICP-CC488 | Installation Guide | 9.0
Domestic Dialing
EN | 42
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
2 – Enable Alarm Link Call Back
If this option is selected and a callback telephone
number is programmed, the remote programming
computer must be connected to the telephone line
programmed in the callback telephone number in
Locations 159 to 174 (refer to Section 11.9 on page
51).
number is programmed, the remote programming
computer must be connected to the telephone line
programmed in the callback telephone number in
Locations 159 to 174 (refer to Section 11.9 on page
51).
If this option is not selected, the installer can connect
to a customer’s control panel from any remote
location for Upload/Download operations without
the control panel calling back to the remote
computer. The customer can initiate a modem call
from the codepad by holding down [6]. Refer to
Section 8.0 Alarm Link Software on page 40 for more
information.
to a customer’s control panel from any remote
location for Upload/Download operations without
the control panel calling back to the remote
computer. The customer can initiate a modem call
from the codepad by holding down [6]. Refer to
Section 8.0 Alarm Link Software on page 40 for more
information.
4 – Terminate Alarm Link Connection on Alarm
If an alarm occurs when the control panel is
communicating with a remote computer using the
CC816 Alarm Link Software, the Alarm Link session
is terminated and the relevant alarm message is
transmitted to the base station receiver.
communicating with a remote computer using the
CC816 Alarm Link Software, the Alarm Link session
is terminated and the relevant alarm message is
transmitted to the base station receiver.
If an alarm occurs that does not have to be reported
to the base station receiver, the session is not
terminated. If this option is not selected and an alarm
occurs, the Alarm Link software prompts the
operator with a Terminate or Continue message.
to the base station receiver, the session is not
terminated. If this option is not selected and an alarm
occurs, the Alarm Link software prompts the
operator with a Terminate or Continue message.
9.0 Domestic Dialing
The locations of the primary and secondary
telephone numbers for Receiver 1 or Receiver 2 are
used only for base station and pager reporting. When
either Receiver 1 or Receiver 2 is set up for domestic
reporting, both the primary and secondary telephone
numbers are ignored.
telephone numbers for Receiver 1 or Receiver 2 are
used only for base station and pager reporting. When
either Receiver 1 or Receiver 2 is set up for domestic
reporting, both the primary and secondary telephone
numbers are ignored.
The domestic dialing telephone numbers are stored
separately in Locations 550 to 597, which can store
up to 48 digits. These 48 locations can store one or
more telephone numbers. Depending on the length
of each telephone number, you can store four or
more different telephone numbers for domestic
dialing.
separately in Locations 550 to 597, which can store
up to 48 digits. These 48 locations can store one or
more telephone numbers. Depending on the length
of each telephone number, you can store four or
more different telephone numbers for domestic
dialing.
If both Receiver 1 and Receiver 2 are set up for
domestic reporting format, you still have 48 data
locations. Both Receiver 1 and Receiver 2 use the
same domestic telephone numbers. Programming
separate domestic telephone numbers for Receiver 1
and Receiver 2 is not available for domestic dialing
format.
domestic reporting format, you still have 48 data
locations. Both Receiver 1 and Receiver 2 use the
same domestic telephone numbers. Programming
separate domestic telephone numbers for Receiver 1
and Receiver 2 is not available for domestic dialing
format.
Refer to Section 9.2 Setting Up and Programming
Domestic Reporting on page 43 for more information.
Domestic Reporting on page 43 for more information.
9.1 Domestic
Dialing
Function
When the control panel is activated into alarm, it
dials the first programmed telephone number. If a
busy or engaged tone is detected, the control panel
hangs up and dials the sec telephone number (if one
is programmed). The first call is counted as one
unsuccessful dialing attempt. If the sec telephone
number is also busy or an engaged tone is detected,
the control panel hangs up and dials the third
telephone number (if one is programmed) or
attempts the first telephone number again.
dials the first programmed telephone number. If a
busy or engaged tone is detected, the control panel
hangs up and dials the sec telephone number (if one
is programmed). The first call is counted as one
unsuccessful dialing attempt. If the sec telephone
number is also busy or an engaged tone is detected,
the control panel hangs up and dials the third
telephone number (if one is programmed) or
attempts the first telephone number again.
If a busy tone is not detected, the control panel
assumes the telephone was answered and sends its
transmission. The transmission sequence consists of
an identification beep, followed by a siren tone and a
long pause. The transmission sequence is repeated
until the control panel receives an acknowledgment
tone during the pause. The control panel
automatically hangs up after 2 min. If more than one
control panel reports to the same telephone number,
the identification beep allows the customer to verify
the control panel that called. The identification beep
is programmed in Location 039 of the Subscriber ID
Number for Receiver 1 or Location 079 of the
Subscriber ID Number for Receiver 2.
assumes the telephone was answered and sends its
transmission. The transmission sequence consists of
an identification beep, followed by a siren tone and a
long pause. The transmission sequence is repeated
until the control panel receives an acknowledgment
tone during the pause. The control panel
automatically hangs up after 2 min. If more than one
control panel reports to the same telephone number,
the identification beep allows the customer to verify
the control panel that called. The identification beep
is programmed in Location 039 of the Subscriber ID
Number for Receiver 1 or Location 079 of the
Subscriber ID Number for Receiver 2.
When set up for Domestic Dialing
Format, the control panel attempts a
maximum of six calls for each alarm event.
This count includes any unsuccessful
calls. The counter is reset if the zone is
reactivated and the control panel
attempts an additional six calls. The
control panel stops dialing after six
attempts or three successful calls. The
control panel also stops dialing if a valid
User Code is entered at the remote
codepad.
Format, the control panel attempts a
maximum of six calls for each alarm event.
This count includes any unsuccessful
calls. The counter is reset if the zone is
reactivated and the control panel
attempts an additional six calls. The
control panel stops dialing after six
attempts or three successful calls. The
control panel also stops dialing if a valid
User Code is entered at the remote
codepad.
If both Receiver 1 and Receiver 2 are
programmed for domestic dialing, the
maximum number of calls for each alarm
event is twelve.
programmed for domestic dialing, the
maximum number of calls for each alarm
event is twelve.
To acknowledge domestic dialing:
If the received call is not acknowledged during any
of the transmission pauses by pressing the [*] button
on a touch-tone telephone, the control panel
continues to send its transmission for two min. Then
it hangs up and dials the next telephone number. If
the call is successfully acknowledged, the control
panel hangs up and makes no more calls for that
event.
of the transmission pauses by pressing the [*] button
on a touch-tone telephone, the control panel
continues to send its transmission for two min. Then
it hangs up and dials the next telephone number. If
the call is successfully acknowledged, the control
panel hangs up and makes no more calls for that
event.