Bosch CC408 User Manual
CC408 | Operators Guide | 6. Disarming the System
EN | 9
Bosch Security Systems | 5/04 | 920050O.OG.112
Arming in STAY Mode 2
Hold down the [0] button until two beeps sound.
The STAY indicator lights and exit time starts
counting.
The STAY indicator lights and exit time starts
counting.
Any zones programmed to be automatically isolated
in STAY Mode 2 flash until exit time expires. At the
end of exit time, all zones selected to be
automatically isolated extinguish and the codepad
provides one short beep.
in STAY Mode 2 flash until exit time expires. At the
end of exit time, all zones selected to be
automatically isolated extinguish and the codepad
provides one short beep.
5.4
Programming STAY Mode 2 Zones
You can only program zones to be automatically
isolated in STAY Mode 2 if you have a Master Code.
isolated in STAY Mode 2 if you have a Master Code.
How to Program STAY Mode 2 Zones
1. Enter your four-character Master Code, followed
by the [4] and [#] keys (for example,
[2 5 8 0 4 #]). Three beeps sound and the STAY
indicator flashes.
[2 5 8 0 4 #]). Three beeps sound and the STAY
indicator flashes.
2. Enter the zone number to be automatically
isolated, followed by the [*] key (for example,
[1 *] = Zone 1, [2 *] = Zone 2).
The selected zone flashes. If you make a mistake,
enter the same zone number followed by the [#]
key to clear the incorrect zone.
To select additional zones to be automatically
isolated in STAY Mode 2, repeat Step 2 as many
times as required.
[1 *] = Zone 1, [2 *] = Zone 2).
The selected zone flashes. If you make a mistake,
enter the same zone number followed by the [#]
key to clear the incorrect zone.
To select additional zones to be automatically
isolated in STAY Mode 2, repeat Step 2 as many
times as required.
3. To exit this mode, press the [#] key when you
have selected all zones to be automatically
isolated in STAY Mode 2. Two beeps sound and
the STAY and AWAY indicators turn dark.
isolated in STAY Mode 2. Two beeps sound and
the STAY and AWAY indicators turn dark.
6.
Disarming the System
When you enter the premises after the system is
armed in AWAY Mode, or if you have armed the
system in STAY Mode 1 or STAY Mode 2, you must
disarm the system before entry time expires to
disable detection devices that activate an alarm. Only
your installer can program the entry time.
armed in AWAY Mode, or if you have armed the
system in STAY Mode 1 or STAY Mode 2, you must
disarm the system before entry time expires to
disable detection devices that activate an alarm. Only
your installer can program the entry time.
If there was an alarm condition prior to disarming
the system, a flashing zone indicator displays
indicating a previous alarm on that zone.
the system, a flashing zone indicator displays
indicating a previous alarm on that zone.
How to Disarm the System
Enter your user code followed by the [#] key (for
example, [2 5 8 0 #]). Two beeps sound.
example, [2 5 8 0 #]). Two beeps sound.
7.
User Codes
7.1
Adding User Codes
Only the Master Code holder can add or change
other system user codes, including the Master Code.
Up to eight user codes can be programmed to
operate the system.
other system user codes, including the Master Code.
Up to eight user codes can be programmed to
operate the system.
How to Add a User Code
1. Enter your four-character Master Code, followed
by [1] and [#] (for example, [2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the user code number (1 to 8) followed by
the [#] key (for example, [2 #] = User 2, [8 #] =
User 8). Two beeps sound and the selected user
number displays on the codepad indicators.
User 8). Two beeps sound and the selected user
number displays on the codepad indicators.
3. Enter the digits required for the new code
followed by the [#] key (for example, for user
code 5768, enter [5 7 6 8 #]). Two beeps sound
and the STAY and AWAY indicators turn dark.
To add or change other user codes, repeat this
procedure as many times as required.
code 5768, enter [5 7 6 8 #]). Two beeps sound
and the STAY and AWAY indicators turn dark.
To add or change other user codes, repeat this
procedure as many times as required.
7.2
Adding Radio Remote User Codes
Only the Master Code holder can add or change
other system user codes, including the Master Code.
Up to eight radio user codes (User Codes 9 to 16)
can be programmed to operate the system.
other system user codes, including the Master Code.
Up to eight radio user codes (User Codes 9 to 16)
can be programmed to operate the system.
How to Add a Radio Remote User Code
1. Enter your four-character Master Code, followed
by the [1] and [#] keys (for example,
[2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
[2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the radio remote user code number (9 to
16), followed by the [#] key (for example, [9 #] =
User 9, [1 6 #] = User 16). Two beeps sound and
the selected user number displays on the
codepad indicators.
User 9, [1 6 #] = User 16). Two beeps sound and
the selected user number displays on the
codepad indicators.
3. Press any button on the keyfob so the system
learns the ID number. Two beeps sound and the
STAY and AWAY indicators extinguish.
To add or change other radio remote user codes,
repeat this procedure as many times as required.
STAY and AWAY indicators extinguish.
To add or change other radio remote user codes,
repeat this procedure as many times as required.
7.3
Deleting User Codes/Radio User
Codes
Codes
Only the Master Code holder can delete other
system user codes.
system user codes.
How to Delete a User Code
1. Enter your four-character Master Code, followed
by the [1] and [#] keys (for example,
[2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
[2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the user code number (User Code 1 to 8,
Radio User Code 9 to 16), followed by the [#]
key (for example, [2 #] = User 2, [1 6 #] = User
16). Two beeps sound and the selected user
number displays on the codepad indicators.
key (for example, [2 #] = User 2, [1 6 #] = User
16). Two beeps sound and the selected user
number displays on the codepad indicators.
3. Press the [*] key to delete the selected user code.
Two beeps sound and the STAY and AWAY
indicators turn dark. To delete other user codes,
repeat this procedure as many times as required.
indicators turn dark. To delete other user codes,
repeat this procedure as many times as required.