Tascam SN29401376 User Manual
Advanced Operations
En-65
Adjusting the Volume for Zone 2
■
Operating on the remote controller
■
Operating on the AV receiver
Muting Zone 2
■
Operating on the remote controller
Tip
• To unmute, press ZONE2 followed by MUTING again. Zone can
also be unmuted by adjusting the volume.
Adjusting the Tone and Balance of Zone 2
Note
• Only analog input sources are output from the ZONE 2
PRE/LINE OUT jacks. Digital input sources are not output. If no
sound is heard when an input source is selected, verify that the
source is connected to an analog input.
sound is heard when an input source is selected, verify that the
source is connected to an analog input.
• You cannot select different AM or FM radio stations for your
main room and Zone 2. The same AM/FM radio station will be
heard in each room. Namely, if you have selected an FM station
for the main room, that station will also be output in Zone 2.
heard in each room. Namely, if you have selected an FM station
for the main room, that station will also be output in Zone 2.
• When you have selected NET or USB as input selector, the last
selector selected will be set for Main room and Zone 2.
• When Zone 2 is activated and its input selector is selected, the
power consumption of standby mode slightly increases.
• While Zone 2 is on,
u functions will not work.
• When setting the AV receiver to standby mode while Zone 2 is
active, the Z2 indicator is dimly lit.
• Activating Zone 2 in the main room when the listening mode is
set to Pure Audio (European models) will automatically switch
it to Direct.
it to Direct.
• The Zone 2 level, balance, and tone functions have no effect on
the ZONE 2 PRE/LINE OUT jacks when the “Zone 2 Out”
setting is set to “Fixed” (
setting is set to “Fixed” (
The 12V triggers A, B, and C can be used to turn on 12V
trigger-capable components automatically when they are
selected as the input source. The triggers can be set so that
they activate themselves once a connected component is
selected as the input source for the main room, Zone 2 or
any combination of rooms. When triggered, the output
from a 12V TRIGGER OUT goes high (+12 volts and
150 milliamperes max. at 12V TRIGGER OUT A;
+12 volts and 25 milliamperes max. at 12V TRIGGER
OUT B and C).
See “12V Trigger A/B/C Setup” (
trigger-capable components automatically when they are
selected as the input source. The triggers can be set so that
they activate themselves once a connected component is
selected as the input source for the main room, Zone 2 or
any combination of rooms. When triggered, the output
from a 12V TRIGGER OUT goes high (+12 volts and
150 milliamperes max. at 12V TRIGGER OUT A;
+12 volts and 25 milliamperes max. at 12V TRIGGER
OUT B and C).
See “12V Trigger A/B/C Setup” (
Hookup
• Use a miniplug cable to connect the AV receiver’s 12V
• Use a miniplug cable to connect the AV receiver’s 12V
TRIGGER OUT A, B, or C jack to the 12 V trigger
input of a connected component.
input of a connected component.
1
Press
ZONE2.
2
Use
VOL
q/w.
1
Press
ZONE 2 (the Z2 indicator on the AV
receiver’s display flashes).
2
Use
MASTER VOLUME control within 8 seconds.
1
Press
ZONE2 followed by MUTING.
1
On the AV receiver, press
ZONE 2.
2
Press the AV receiver’s
TONE repeatedly to select
“Bass”, “Treble” or “Balance”.
3
Use
–/+ to adjust the bass, treble or balance.
• You can boost or cut the bass or treble from –10 dB
to +10 dB in 2 dB steps.
• You can adjust the balance from 0 in the center to
+10 dB to the right or +10 dB to the left in 2 dB
steps.
steps.
Using the 12V Triggers