Yamaha RX-Z7 User Manual

Mosquito NR (Mosquito noise reduction)
Mosquito noise is a type of noise that appears along 
edges of compression artifacts. Use this feature to 
adjust the mosquito noise reduction level.
Choices: Off, Low, Medium, High

Block NR (Block noise reduction)
Block noise is often caused when the bitrate is too 
low to accurately encode the video. Use this feature 
to adjust the block noise reduction level.
Control range: 0 to 50

Detail Enhancement (Detail enhancement)
Use this feature to adjust finesses of images.
Control range: 0 to 50

Edge Enhancement (Edge enhancement)
Use this feature to adjust sharpness of images.
Control range: 0 to 50

Brightness (Brightness)
Use this feature to adjust brightness of images.
Control range: -50 to 50
Initial setting: 0

Contrast (Contrast)
Use this feature to adjust contrast of images.
Control range: -50 to 50
Initial setting: 0

Saturation (Saturation)
Use this feature to adjust saturation of images.
Control range: -50 to 50
Initial setting: 0

Use this feature to set the HDMI functions or check the 
information about the video monitors connected to the 
HDMI OUT jacks.

■ Standby Through (Standby through)

Mode (Standby through mode)
Use this feature whether this unit allows the HDMI signals 
input at the HDMI IN jacks to pass thorough this unit 
when this unit is in the standby mode. You can also 
designate an HDMI IN jack and HDMI OUT jack(s) that 
accept the signals when “Mode” is set to “Fix” and this 
unit is in the standby mode.

When “Mode” is set to “Last” or “Fix”, the amount of power 
consumption in the standby mode increases.

Input (HDMI IN jack select)
Use this feature to select an HDMI IN jack that accepts 
HDMI signals when this unit is in the standby mode.

This setting is available only when “Mode” is set to “Fix”.

Output (HDMI OUT jack select)
Use this feature to select HDMI OUT jack(s) that output 
HDMI signals when this unit is in the standby mode.

This setting is available only when “Mode” is set to “Fix”.

■ Audio Output (HDMI audio output)

Use this feature to select whether to play back HDMI 
audio signals on this unit or on another HDMI component 
connected to the HDMI OUT jacks on the rear panel of 
this unit.

y

If “Audio Output” is set to “TV” or “Amp + TV”, available 
audio signals vary depending on the specification of the 
connected video monitor.

Disables the HDMI standby through feature. 
HDMI signals do not pass through this unit if 
this unit is in the standby mode.

Last

HDMI signals pass through this unit (only from 
the HDMI IN jack to the HDMI OUT jack(s) 
used when this unit is set to the standby mode) 
even when this unit is in the standby mode.

Fix

HDMI signals pass through this unit (from the 
HDMI IN jack specified in “Input” to the HDMI 
OUT jack(s) specified in “Output”) even when 
this unit is in the standby mode.

IN1

HDMI IN1 (BD/HD DVD) jack

IN2

HDMI IN2 (DVD) jack

IN3

HDMI IN3 (CBL/SAT) jack

IN4

HDMI IN4 (DVR) jack

Front

HDMI IN (VIDEO AUX) jack

HDMI OUT 1 and HDMI OUT 2 jacks

OUT1

HDMI OUT 1 jack

OUT2

HDMI OUT 2 jack

Outputs HDMI audio signals at the speakers 
connected to this unit.

TV

Outputs HDMI audio signals at the speakers of 
the TV connected to this unit. The speakers 
connected to this unit are muted.

Amp + TV

Outputs HDMI audio signals at the speakers 
connected to this unit and speakers of the TV 
connected to this unit.