Korg SP-500 User Manual
54
OVDB
(overdub): The newly recorded
data will be added to the previously-
recorded data.
AUTP
recorded data.
AUTP
(auto punch-in/out): Auto punch-
in/out recording will be performed.
In the “Rec 1/3” page, “OVWR” will be used
regardless of this setting.
For “OVWR” and “OVDB,” the “start mea-
sure” cell and the “end measure” cell settings
are ignored.
regardless of this setting.
For “OVWR” and “OVDB,” the “start mea-
sure” cell and the “end measure” cell settings
are ignored.
To change the name of the song
Recording from the middle of the
song
song
1
Select the performance data that
you saved
you saved
2
Play back the recorded song
Set each track to “Play,” and press the
[PLAY/STOP] switch.
[PLAY/STOP] switch.
3
When you come to the measure
that you wish to record, pause
the playback
that you wish to record, pause
the playback
When playback reaches the measure at
which you wish to begin recording, press
the [PAUSE] switch to pause.
which you wish to begin recording, press
the [PAUSE] switch to pause.
4
Select the track that you wish to
record
record
Change the setting to “Rec” for the track
that you wish to additionally record.
• When recording with the [ACC] switch
that you wish to additionally record.
• When recording with the [ACC] switch
on, the KBD, CTRL, and CHORD
tracks.
tracks.
• When recording with the [ACC] switch
off, the KBD and CTRL tracks.
• When recording tracks 1 – 5, the corre-
sponding track.
5
Defeat pause
Press the [PAUSE] switch to defeat pause.
After a two-measure pre-count, recording
will begin.
After a two-measure pre-count, recording
will begin.
Auto punch-in/out
If you made a mistake or did not obtain the desired
result in one location of a recorded song, you can
re-record just that location without having to re-
record from the beginning of the song. Auto Punch
In
result in one location of a recorded song, you can
re-record just that location without having to re-
record from the beginning of the song. Auto Punch
In
is the action of automatically switching from
playback into record mode at the previously speci-
fied measure. Conversely, Auto Punch Out is the
action of automatically switching from record
mode into playback at the specified measure.
fied measure. Conversely, Auto Punch Out is the
action of automatically switching from record
mode into playback at the specified measure.
This function can be used on tracks 1–5.
1
Select the performance data that
you saved
you saved
2
Pause at a point earlier than the
measures you wish to re-record
measures you wish to re-record
Set each track to “Play,” and press the
[PLAY/STOP] switch. Two or three mea-
sures before the measure at which you
will begin re-recording, press the
[PAUSE] switch.
[PLAY/STOP] switch. Two or three mea-
sures before the measure at which you
will begin re-recording, press the
[PAUSE] switch.
3
Select the track that you wish to
re-record
re-record
For the track that you wish to re-record,
press the “Track” button to select “Rec”.
press the “Track” button to select “Rec”.
The following settings cannot be made unless
you select “Rec.”
you select “Rec.”
4
In the “Rec 2/3” page, set the
“Recording mode” cell to
“AUTP.”
“Recording mode” cell to
“AUTP.”
Press the “Recording mode” cell, and use
the dial or the [VALUE] switches to select
“AUTP.”
the dial or the [VALUE] switches to select
“AUTP.”
5
Set the “start measure” cell
Press the “start measure” cell, and use the
dial or the [VALUE] switches to specify
the measure at which you will begin re-
recording.
dial or the [VALUE] switches to specify
the measure at which you will begin re-
recording.
“Recording mode”
“Start” “End”