Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. TQBJ0349
  5. User Manual

Panasonic TQBJ0349 User Manual

Download
Page of 95
PROJECTOR SETUP menu
ENGLISH - 
65
Settings
Press ▲▼ to select [TIME] or 
4 ) 
[COMMAND] and change the setting 
according to the instructions of the 
menu.
TIME
Set the time at which the command 
will be executed using ▲▼ buttons.
COMMAND
Select a command to execute at the 
set time from the following.
POWER ON
• 
STANDBY
• 
AV MUTE ON
• 
AV MUTE OFF
• 
INPUT RGB1
• 
INPUT RGB2
• 
INPUT VIDEO
• 
INPUT S-VIDEO
• 
INPUT DVI-D
• 
INPUT HDMI
• 
INPUT 
• 
NETWORK
LAMP POWER 
• 
NORMAL
LAMP POWER 
• 
ECO
SIDE BY SIDE 
• 
MODE OFF
SIDE BY SIDE 
• 
MODE1
SIDE BY SIDE 
• 
MODE2
SIDE BY SIDE 
• 
MODE3
SIDE BY SIDE 
• 
MODE4
IN STANDBY 
• 
MODE (AUDIO) 
ON
IN STANDBY 
• 
MODE (AUDIO) 
OFF
VOLUME
• 
PT-DZ570U/PT-DW530U only
: 
Û
Press ▲▼ to select [STORE] and 
5 ) 
press <ENTER> button.
Note
If you try to register a setting that would cause the lamp to 
 
z
flash for a short time, an error message will be displayed on 
the screen. Set the [TIME] and [COMMAND] again.
To delete a command which has been set, press 
 
z
<DEFAULT> button.
If multiple commands have been set for the same time, 
 
z
they are executed in chronological order starting from the 
smallest command number.
The setting time operates under the local time.  
 
z
(
Æ
page 67)
If an operation is executed with the remote control or 
 
z
control panel of the projector or with a control command 
before the command set in the schedule is executed, the 
command set with this function may not be executed.
RS-232C
This sets the communication parameters at the serial 
terminals.
Press ▲▼ to select [RS-232C].
1 ) 
Press <ENTER> button.
2 ) 
The [
 
z
RS-232C] screen will be displayed.
Press ▲▼ to select communication 
3 ) 
conditions.
press ◄► to change the setting.
4 ) 
Note
Refer to 
 
z
Æ
page 82).
 
J
Selecting items in [EMULATE]
When using the control commands for one of our 
projectors that you have previously purchased to 
control this projector using a computer via its serial 
input terminal, set up the EMULATE function as 
follows. This will allow you to use the control software 
etc. designed for our existing projectors.
Select [EMULATE] in step 3).
1. 
Press <ENTER> button.
2. 
Press ▲▼ to select the required item.
3. 
Press <ENTER> button.
4. 
● DEFAULT
DZ570 Series, DW530 Series, 
DX500 Series
L730  
SERIES
L520 Series, L720 Series, 
L730 Series
L780  
SERIES
L750 Series, L780 Series
L735  
SERIES
L735 Series
L785  
SERIES
L785 Series
F SERIES
F100 Series, FW100 Series, 
F200 Series, F300 Series, 
FW300 Series 
LB SERIES
LB75 Series, LB78 Series, 
LB80 Series, LB90 Series, 
LB1 Series, LB2 Series, 
ST10 Series