Cuisinart B70 User Manual

 1. 

Unwrap cord and plug the Brewer into a 
grounded outlet. Remove all pieces of  

packing tape and clear plastic sticker from  
LCD Control Center.

 2.

  Place a large mug (10 oz. minimum) on the Drip 

Tray Plate.

 3.

  Remove the Water Reservoir from Brewer by 

first removing Lid from the Water Reservoir  
(fig. 1), then lifting the Water Reservoir straight 
up and toward front of Brewer (may be tight),  
(fig. 2 A). Rinse with fresh water.

 4.

  Fill Water Reservoir with bottled or filtered water 

so that the water level is just below the top edge 
of the Water Reservoir.

 5.

  Place Water Reservoir base into the left side of the Brewer and be sure 

the Water Reservoir Lock Tab engages with the Brewer. Replace Lid on 
Water Reservoir. NOTE: Please ensure the Water Reservoir is seated 
properly, so that the back of the Water Reservoir is flush with the Brewer 
(fig. 2 B and C). 

Lock Tab

Seated Properly

 6.

  Press and release the Power Switch found 

directly behind the right side of the Brewer. 

Switch is spring loaded and will return to 

original position.

 7.

  The blue LCD Control Center will come on and 

indicate “NOT READY.” NOTE: A K-Cup

®

 pack 

should not be used for this sequence

.

 8.

  The Brewer will automatically fill the internal 

tank with water and then the water will be 
heated. This will take about 4 minutes.  
During the heating period, “NOT READY”  
is indicated on the LCD Control Center (fig. 3).  
Do not lift Brewer Handle during this heating 
period. Once the water is heated, “READY TO 
BREW” will be indicated and the BREW Button 
will be illuminated (fig. 4). NOTE: You may see 

SECTION 1 

 

Set-Up & First Brew

 5. 

Place a K-Cup

®

 pack in the K-Cup

®

 Pack 

Holder (fig. 6). CAUTION: There are two sharp 
needles that puncture the K-Cup

®

 pack, one 

above the K-Cup

®

 Pack Holder and the other in 

the bottom of the K-Cup

®

 Pack Holder. To avoid 

risk of injury, do not put your fingers in the 
K-Cup

®

 Pack Assembly Housing.

 6. 

Lower the Handle to close the Lid over the 

K-Cup

®

 Pack Holder. (When it is closed 

completely, the LCD Control Center will 

indicate “READY TO BREW.” The Left and 
Right Buttons will be lit and the BREW Button 
will flash up to 60 seconds.)

 a.

 All brew size icons are lit with the default  

size flashing (fig. 7). To choose a different size,  
press Left Button to go down in size or Right 
Button to go up in size. NOTE: The Small Mug is 

the factory set default brew size. To program 
your favorite brew size see page 13 

“Programming Your Brew Size.”

 b.

  Your choices are a stronger Extra-Small  

Cup (3.25 oz. serving), a Small Cup (5.25 oz. 

serving), a Small Mug (7.25 oz. serving), a 
Large Mug (9.25 oz. serving) or a Travel Mug 
(11.25 oz. serving).

small amounts of water coming from the Vent 
and dripping into the Water Reservoir during 

this and subsequent heating — this is normal.

 9.

  Lift and lower the Handle. Press the flashing 

BREW Button to start a cleansing brew 
without a K-Cup

®

 pack. Pour the hot water 

into the sink. NOTE: A K-Cup

®

 pack should not 

be used for this sequence

.

 10.

 The one-time set-up process is now  

complete and you are ready to brew! 

NOTE: The Brewer may take 15-30 seconds  
between brews and then “READY TO BREW”  
will be indicated.

  1. LCD Control Center will indicate  

“READY TO BREW.” 

 2. 

Place a cup or mug on the Drip Tray Plate.

 3. 

Lift the Handle and the K-Cup

®

 Pack  

Holder will open toward you (fig. 5).

 4. 

Select a K-Cup

®

 pack.  

NOTE: Do not remove the foil  
lid or puncture the K-Cup

®

 pack.

IMPORTaNT: You cannot use your Keurig

®

 Brewer until it has been set 

up for its first use.
NOTE: If Brewer has been exposed to temperatures below freezing, 

allow Brewer at least two hours to reach room temperature before 

brewing. A frozen or extremely cold Brewer will not operate.

6

7

Not Seated Properly