Cuisinart B70 User Manual

11

10

SECTION 2

  

Controls & Indicators (LCD Control Center)

 b.  Press or hold the Left Button under the 

blinking “H” to advance 1 hour at a time, up  
to 9 hours. 

  c.   After setting the desired Auto Off time, press 

the MENU Button five times to scroll through 
the remaining programming options and exit 
the programming mode. “AUTO OFF SET”  
(fig. 12) will now be displayed to indicate that it 
has been set. 

 d.   To cancel the Auto Off feature, press the 

MENU Button twice to reach the “AUTO OFF” 
programming mode. Press and release the 
Left Button under the blinking “H” to advance 
one hour at a time until “OFF” is indicated.

 3.  Program your Brewer for a specific On/Off 

Time.

 NOTE: To use this programming feature, 

the clock must be set to the correct time. The 

clock will not be displayed unless the time is set.

 a.   After setting the correct time (required), press 

the MENU Button three times to program On 

Time feature. The LCD Control Center will 

show the programming options with a small 
arrow next to “SET ON TIME” (fig. 13). 

 b.   Press or hold the Left Button under the “H”  

to scroll through the hours to your desired 

“ON TIME” hour.

Setting the clock is optional. When the clock is set, the time will appear in the 
LCD Control Center. NOTE: You must set the clock if you will be using the Auto 
On/Off Time programming feature.

 1. 

Press the MENU Button.

 2.

  The word “OFF” will appear at the top of the 

LCD Control Center to indicate that the clock 
is not set (fig. 10). The programming options 
will appear on the LCD Control Center with a 
small arrow pointing to “SET CLOCK.”  

“H” (Hour) will appear above the Left Button 

and “M” (Minute) will appear above the Right 
Button. The “H” and “M” icons and Left and 
Right Buttons will flash.

 3.

  Press or hold the Left Button under the 

flashing “H” until you have reached the 
appropriate hour. If the hour has passed  

12 “PM” will be shown.

 4.

  Press or hold the Right Button under the 

flashing “M” to set the minutes.

 5.

  When you have reached the correct time, press the MENU Button six 

times to scroll through the remaining programming steps.

Set

Hours

Set

Minutes

 6.

  The correct time should now be displayed in the LCD Control Center. 

NOTE: If power is interrupted to the Brewer by unplugging it, or if power is 
lost, follow the procedure above to reset the time as the clock will not be 
visible until the time is set. Brew size and brew temperature menu settings 

are remembered and restored automatically. All other settings will be 
restored automatically after clock is set.

The Brewer provides three modes so that you can enjoy gourmet coffee, tea 

or hot cocoa on your own schedule. By programming your Brewer to turn on 
each morning, you will never have to wait for the Brewer to warm up to brew 
a gourmet cup of coffee. It will take the Brewer approximately 4 minutes to 

warm up from room temperature.

  1.  Leave it ON all the time.

 The Brewer can be left on all the time so that it is 

always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To 
turn the Brewer off at any time, simply press and release the Power 
Switch. (NOTE: Although the clock remains on, if set, you can not brew a cup 
of coffee, tea or hot cocoa.) 

Press and release the Power Switch again to 

restore power to the Brewer. You will have to wait for the water to heat up 
before the Brewer is ready to brew.

 2. Set the Brewer to “AUTO OFF” following a specified period of time after the 

last brew. 

 a.  Press the MENU Button twice to program the Auto Off feature. The LCD 

Control Center will now display the programming options with a small 
arrow next to “SET AUTO OFF” (fig. 11).

  c.  Press or hold the Right Button under the “M” 

to scroll through the minutes to your desired 

“ON TIME” minutes.

 d.  After setting the desired time, press the 

MENU Button to save the “ON TIME” and  
move to the “SET OFF TIME” (fig. 14). 

 e.  If you want to set an “OFF TIME,” repeat the 

procedure above in steps b & c to set your 
desired “OFF TIME” (fig. 14). 

  f.  To complete the process, press the MENU 

Button three more times to exit the 
programming mode. The Control Center  
will now indicate the options you have set.

 g.  The Auto On time and Auto Off time functions 

operate independently from one another. To 
cancel either set function, follow the steps 
above and use the “H” and “M” Buttons to 
advance to 12:00 AM. Make sure the “M” 
Button is set to :00, then change the “H” 
Button. When you reach 12:00 AM, the  

Control Center will indicate “OFF” and the 
function will be disabled.

 If you chose to set the On Time at 

6:55 AM and the Off Time for 10:00 PM, then 

the Brewer will be “READY TO BREW” and 
maintain hot water in the tank during that  
time so that it is always ready for you to brew. 
If you wanted to brew outside this window,  

Set

Hours

Set

Minutes

Set

Hours

Set

Minutes