DeLonghi 10.13 User Manual

13

2.  Place under the coffee dispensing spouts, either:
 

- 1 cup if you want one coffee (fig. 14);

 

 - 2 cups if you want 2 coffees.

3.  Lower the spouts as near as possible to the cup. This 

makes a creamier coffee (fig. 15). 

4.  Press the button corresponding to the number of coffees 

required (1 cup 

 or 2 cups 

,  figs. 11 and 

16).  

5.  Preparation begins. The amount of coffee selected is dis-

played together with a progress bar which gradually fills 
as preparation progresses. 

•  While the machine is making coffee, delivery can be inter-

rupted at any moment by pressing any button. 

•  At the end of delivery, to increase the quantity of coffee 

in the cup, just press (within 3 seconds) one of the coffee 
buttons (

or 

).

Once the coffee has been made, the appliance is ready to make 
the next drink.

•  Various alarm messages could be displayed while using 

the machine (FILL TANK, EMPTY GROUNDS CONTAINER, 
etc.). Their meaning is explained in the section “Displayed 
messages” (page 20).

•  For hotter coffee, see the section “Tips for a hotter coffee”  

(page 12).

•  If the coffee is delivered a drop at a time, too weak and not 

creamy enough or too cold, read the tips in the “Trouble-
shooting” section on page 21.

•  Never add pre-ground coffee 

when the machine is off or it 
could spread through the inside 
of the machine and dirty it. 

  This could damage the 

appliance.

•  Never use more than 1 level measure or it could dirty the

inside of the coffee maker or block the funnel.

 

If you use pre-ground coffee, you can only make one cup 
of coffee at a time. 

1.  Press the

button (fig. 7) repeatedly until “Pre-

ground” is displayed. 

2.  Open the beans container lid; then open the pre-ground 

coffee funnel lid by pushing on PUSH and, once released, 
open the lid. 

3.  Make sure the funnel is not blocked, then add one level 

measure of pre-ground coffee (fig. 17).

4.  Place a cup under the coffee spouts.
5.  Press the 1 cup coffee button 

(fig. 11).   

6.  Preparation begins. The amount of coffee selected is dis-

played together with a progress bar which gradually fills 
as preparation progresses. 

If “Energy saving” mode is enabled, you may have to wait a few 
seconds before the first coffee is delivered.

•  To avoid producing milk with poor froth or large bubbles, 

always clean the milk container lid and hot water nozzle 
as described in the section “Cleaning the milk container” 
on pages 17. 

Filling and attaching the milk container
1.  Remove the lid (fig. 18); 
2.  Fill the milk container with a sufficient quantity of milk,

not exceeding the MAX level marked on the container (fig. 
19).  Each mark on the side of the container corresponds 
to 100 ml of milk. 

•  For a denser more even froth, you should use skimmed or 

partially skimmed milk at refrigerator temperature (about 
5°C).  

•  If “energy saving” mode is enabled, you may have to wait

a few seconds before the first cappuccino is delivered.

3.  Make sure the milk intake tube is correctly inserted in the 

bottom of the milk container lid  (fig. 20).

4.  Place the lid back on the milk container. 
5.  Remove the hot water spout from the nozzle, by pressing 

the button.

6.  Attach the container to the nozzle and push as far as it 

will go (fig. 21). The machine emits a beep (if the beep 
function is enabled).

7.  Place a sufficiently large cup under the coffee and frothed

milk spouts. Adjust the length of the milk spout. To move 
it nearer the cup, simply pull it downwards (fig. 22).

8.  Follow the instructions below for each function.